{"title":"Dishwasher Parts","description":null,"products":[{"product_id":"524285p-genuine-fisher-and-paykel-dishdrawer-motor-rotor-assembly-ph5","title":"524285P Genuine DishDrawer Motor Rotor Assembly PH5 for Fisher \u0026 Paykel Dishwashers DD605 DD60DCX6 DD60DCX7 DD60SCTX7 DD60DI7 DS605","description":"\u003cp\u003eBuilt for PH5 DishDrawers, 524285P is the genuine Fisher \u0026amp; Paykel wash motor rotor, the version with a notch. It's listed for the DD605 and DS605 models, plus DD60 drawers ending in 6 and 7, such as DD60DCX6, DD60DCX7, DD60SCTX7 and DD60DI7. Fisher \u0026amp; Paykel also make a similar looking rotor, 524922P, for later drawers, and the two are not interchangeable.\u003c\/p\u003e\n\u003ch2\u003eDishDrawer not washing or making grinding noises\u003c\/h2\u003e\n\u003cp\u003eIn a DishDrawer the wash pump motor is built into the base of the drawer, and the rotor is the part that spins inside it to drive the impeller. A damaged rotor can cause grinding or rattling during the wash, a weak spray, dishes coming out dirty, or the drawer stopping with a motor or pump fault. Broken glass, grit and small bones drawn into the pump are common causes. Check the filter and sump area for debris at the same time, or the new rotor can suffer the same fate.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 524285P\u003c\/li\u003e\n\u003cli\u003ePH5 motor rotor assembly with notch\u003c\/li\u003e\n\u003cli\u003eAlso listed as 528136P\u003c\/li\u003e\n\u003cli\u003eNot interchangeable with 524922P\u003c\/li\u003e\n\u003cli\u003eListed for DD605, DS605 and DD60 drawers ending in 6 and 7\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting the rotor\u003c\/h2\u003e\n\u003cp\u003eRead the model and product code from the compliance label before ordering, because the two F\u0026amp;P rotors look much alike. To fit it, switch the dishwasher off at the wall, then remove the drawer filter and spray arm to reach the pump area. Seat the rotor carefully so the seals aren't damaged, refit the spray arm and run a rinse while listening for any rubbing.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eHow do I tell 524285P and 524922P apart?\u003c\/h3\u003e\u003cp\u003e524285P is the PH5 rotor with a notch, listed for DD605, DS605 and DD60 models ending in 6 or 7. 524922P suits the later DD60 models ending in 8 and 9. Go by your model and product code, not by looks.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547068395598,"sku":"524285P","price":121.84,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/524285p-genuine-fisher-and-paykel-dishdrawer-motor-rotor-assembly-ph5.jpg?v=1792025516"},{"product_id":"758974128-oem-dishwasher-sump-to-air-break-hose","title":"758974128 OEM Sump to Air Break Hose suits Smeg Dishwashers DWA6214X DWA6314X DWAU6314X DWA314X DWA149S DWAI6314X DWAFI6214 DWA3148","description":"\u003cp\u003eThis OEM hose replaces Smeg part number 758974128, the hose that links the sump to the air break in many Smeg dishwashers. It's made to the original equipment specification and listed for the DWA6314X and DWA6214X, the DWAU6314X and DWAI6314X, the DWA314X and DWA3148, and the DWA149S, DWAFI6214 and DWAU315X. Matching the model on your rating label is the easiest way to confirm the fit.\u003c\/p\u003e\n\u003ch2\u003eSmeg dishwasher leaking or stopping with water in the base\u003c\/h2\u003e\n\u003cp\u003eThe air break is a chamber, usually on the side of the tub, that separates the dishwasher's water from the household supply. This hose carries water between that chamber and the sump at the bottom of the tub. Rubber hoses harden and crack with years of hot water and detergent, and a split usually leaks into the base of the machine. Many dishwashers have a float switch there that stops the wash and runs the drain pump when it senses water. So the signs are a puddle under the machine, a cycle that stops partway, an anti-flood error, or the pump running non-stop.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eOEM replacement for Smeg part 758974128\u003c\/li\u003e\n\u003cli\u003eConnects the sump to the air break\u003c\/li\u003e\n\u003cli\u003eMade to the original equipment specification\u003c\/li\u003e\n\u003cli\u003eListed for Smeg DWA, DWAU, DWAI and DWAFI dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eReplacing the sump hose\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off at the wall, shut the tap and pull the machine out. Mop out any water in the base tray and dry the float switch area, otherwise the anti-flood protection may keep tripping. Note the hose routing, release the clamps and fit the new hose, pushing each end fully over its spigot. Refit the clamps, run a short program and check for leaks before sliding it back in.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs this hose made by Smeg?\u003c\/h3\u003e\u003cp\u003eNo. It's an OEM part made to the original equipment specification to replace Smeg number 758974128. It's listed for the Smeg models shown here, so check your model number against the list before ordering.\u003c\/p\u003e","brand":"Astelav","offers":[{"title":"Default Title","offer_id":44547068559438,"sku":"758974128_O","price":23.49,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/758974128-oem-dishwasher-sump-to-air-break-hose.jpg?v=1792025585"},{"product_id":"dw2kgss-genuine-universal-dishwasher-softener-salt-2kg","title":"DW2KGSS Aktivo Dishwasher Softener Salt 2kg, Refill for the Salt Reservoir on Dishwashers with a Built-in Water Softener","description":"\u003cp\u003eAktivo DW2KGSS is a 2kg pack of dishwasher softener salt for machines that have a built-in water softener. The salt goes into the reservoir in the floor of the tub, usually under the lower basket, and keeps the softener working so the wash water stays soft. If your dishwasher has a salt indicator light or a screw cap in the base of the tub, this is the refill it's asking for.\u003c\/p\u003e\n\u003ch2\u003eWhat dishwasher salt does and when to top it up\u003c\/h2\u003e\n\u003cp\u003eMany dishwashers soften the incoming water with a resin unit. Over time the resin fills up with calcium and magnesium from hard water, and the machine flushes it with brine made from the salt in the reservoir to bring it back. Run out of salt and the softener stops doing its job. The usual signs are a cloudy white film on glasses, chalky spots on plates and cutlery, a salt warning light on the panel, and scale building up on the heating element and spray arms. Salt is not a detergent, so it works alongside your normal tablets or powder rather than replacing them.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePart number DW2KGSS\u003c\/li\u003e\n\u003cli\u003e2kg pack of Aktivo dishwasher softener salt\u003c\/li\u003e\n\u003cli\u003eRefills the salt reservoir on dishwashers with a built-in water softener\u003c\/li\u003e\n\u003cli\u003eUsed alongside your usual dishwasher detergent\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e2kg\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFilling the salt reservoir\u003c\/h2\u003e\n\u003cp\u003ePull out the lower basket and unscrew the cap on the reservoir in the floor of the tub. Check your dishwasher manual first, as many machines need the reservoir filled with water before the very first salt fill. Pour the salt in with a funnel, wipe any spilt grains off the thread and seal, and screw the cap down firmly. Run a rinse or a full wash straight away so loose salt doesn't sit in the tub.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDoes my dishwasher need softener salt?\u003c\/h3\u003e\u003cp\u003eOnly if it has a built-in water softener. Look for a screw cap in the floor of the tub under the lower basket, or a salt symbol on the control panel. If your machine has neither, it has no softener and salt isn't needed.\u003c\/p\u003e\n\u003ch3\u003eCan I use table salt instead?\u003c\/h3\u003e\u003cp\u003eNo. Table salt and cooking salt contain additives and fine grains that can clog the softener. Stick with a salt made specifically for dishwashers, like this Aktivo pack.\u003c\/p\u003e","brand":"Aktivo","offers":[{"title":"Default Title","offer_id":44547260481614,"sku":"DW2KGSS","price":12.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/dw2kgss-genuine-universal-dishwasher-softener-salt-2kg.jpg?v=1792025751"},{"product_id":"524922p-genuine-fisher-and-paykel-dishdrawer-motor-rotor-assembly","title":"524922P Genuine DishDrawer Motor Rotor Assembly for Fisher \u0026 Paykel Dishwashers DD60DCX9 DD60SCX9 DD60DAX8 DD60D4NX9 DD60SI9 DD60ST4NB9","description":"\u003cp\u003eFisher \u0026amp; Paykel 524922P is the genuine motor rotor assembly for later DishDrawer models in the DD60 series ending in 8 and 9. Examples include the DD60DAX8 and DD60DCX9, the DD60SCX9 and DD60D4NX9, and the DD60SI9 and DD60ST4NB9, covering both single and double drawer versions. It looks a lot like the older 524285P rotor, but the two won't swap between machines.\u003c\/p\u003e\n\u003ch2\u003eSymptoms of a worn DishDrawer wash motor rotor\u003c\/h2\u003e\n\u003cp\u003eEach drawer has its own wash pump, driven by a motor built into the base of the tub. The rotor is the magnetic part that turns inside that motor and spins the impeller, which pushes water up through the spray arm. When it's damaged, the drawer may run but leave food on the dishes, sound gravelly while washing, or stop part way through with a pump related fault. Debris such as broken glass, bones or fruit stones caught in the pump is a frequent culprit.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 524922P\u003c\/li\u003e\n\u003cli\u003eMotor rotor assembly for DD60 DishDrawers ending in 8 and 9\u003c\/li\u003e\n\u003cli\u003eFits single and double drawer models listed\u003c\/li\u003e\n\u003cli\u003eNot interchangeable with 524285P\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eBefore you start\u003c\/h2\u003e\n\u003cp\u003eIsolate power at the wall. Take the filter and spray arm out of the drawer to expose the pump. Clean out any debris you find around the impeller, as whatever damaged the old rotor can damage the new one. Seat the replacement squarely, reassemble the drawer and run a short program to confirm the wash sounds smooth.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWhere do I find my DishDrawer model and product code?\u003c\/h3\u003e\u003cp\u003ePull the drawer out and look for the compliance label, usually on the side of the drawer frame. It shows a model number like DD60DCX9 and a product code, and both help confirm you're ordering the right rotor.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547261071438,"sku":"524922P","price":152.17,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/524922p-genuine-fisher-and-paykel-dishdrawer-motor-rotor-assembly.jpg?v=1792025518"},{"product_id":"900403743-genuine-electrolux-dishwasher-descaler-powder-350g","title":"900403743 Genuine Dishwasher Descaler Powder 350g for Electrolux, Dishlex, Westinghouse, Simpson, AEG Dishwashers DSF6205W ESL6610RO WSF6606X","description":"\u003cp\u003eHard water leaves scale on the element, spray arms and filters of most dishwashers sooner or later. Electrolux 900403743 is the brand's own 350g descaler powder, also sold as ACC103, made for Electrolux group dishwashers. Models on file include the Dishlex DSF6205W and DSF6206X, the Electrolux ESL6610RO, Westinghouse WSF6606X, Simpson SSF6106W and several AEG models such as F77602M0P.\u003c\/p\u003e\n\u003ch2\u003eCloudy glasses and a smelly dishwasher? Time to descale\u003c\/h2\u003e\n\u003cp\u003eLimescale builds up wherever hot water sits or sprays, and grease and detergent residue stick to it. On the heating element, scale acts like insulation, so the machine takes longer to heat the water. In the spray arms it partly blocks the jets, and in the sump it traps food residue that starts to smell. Run the descaler through an empty dishwasher when you notice white crust on the tub or door, chalky glasses, weak wash results or a musty odour. It's made to remove calcium scale and built-up grease from inside the machine.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Electrolux product 900403743\u003c\/li\u003e\n\u003cli\u003eAlso sold as ACC103\u003c\/li\u003e\n\u003cli\u003e350g of descaler powder\u003c\/li\u003e\n\u003cli\u003eRemoves limescale and greasy residue from inside the dishwasher\u003c\/li\u003e\n\u003cli\u003eFor Electrolux, Dishlex, Westinghouse, Simpson and AEG dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e350g\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eHow to use the descaler\u003c\/h2\u003e\n\u003cp\u003eAlways follow the directions printed on the pack. In general, the dishwasher should be empty of dishes and the powder goes in before you start a hot program. Clean the filters first so loose debris doesn't recirculate through the machine. Store the product away from children, and don't mix it with other cleaning chemicals.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eHow often should I descale my dishwasher?\u003c\/h3\u003e\u003cp\u003eIt depends on how hard your water is and how often you run the machine. Check the pack and your dishwasher manual for guidance, and descale whenever white scale appears in the tub or glasses start coming out cloudy.\u003c\/p\u003e","brand":"Electrolux","offers":[{"title":"Default Title","offer_id":44547261136974,"sku":"900403743","price":19.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/900403743-genuine-electrolux-dishwasher-descaler-powder-350g.jpg?v=1792025590"},{"product_id":"512818-genuine-fisher-and-paykel-dishdrawer-crockery-insert-with-front-and-back-clips","title":"512818 Genuine DishDrawer Crockery Insert with Front and Back Clips for Fisher \u0026 Paykel Dishwashers DD60DCX7 DD60SCX7 DD60DI7 DD60DAX8 DD90SDFTX2","description":"\u003cp\u003ePart 512818 is the genuine crockery insert for Fisher \u0026amp; Paykel DishDrawers, supplied with its front and back clips. It fits into the drawer's basket and keeps crockery in place for washing. The insert replaces 523627 and is listed for DD60 drawers ending in 7, such as the DD60DCX7, the DD60SCX7 and the DD60DI7, some later models like the DD60DAX8 and DD60DCX9, and the DD90SDFTX2.\u003c\/p\u003e\n\u003ch2\u003eBroken DishDrawer rack insert\u003c\/h2\u003e\n\u003cp\u003eInside each drawer, the basket is fitted with inserts that space out the crockery so the spray can reach every surface. If an insert breaks, loses its clips or has tines snapped off, dishes lean into each other, rattle around during the wash and come out with food still on them. A loose insert can also lift and catch the spray arm, stopping it from turning. Replacing a damaged insert is quick, and the clips that come with this part mean it locks into the basket properly.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 512818\u003c\/li\u003e\n\u003cli\u003eReplaces 523627\u003c\/li\u003e\n\u003cli\u003eSupplied with the front clip and back clip 524146\u003c\/li\u003e\n\u003cli\u003eListed for DD60 and DD90 DishDrawers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting the insert\u003c\/h2\u003e\n\u003cp\u003eNo tools are needed. Empty the drawer and lift out the old insert, noting how it locates in the basket. Fit the front and back clips the same way the old ones sat, then press the new insert into place until it sits flat. Spin the spray arm by hand to make sure nothing catches on it before running a wash.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eMy drawer has two inserts. Which one is this?\u003c\/h3\u003e\u003cp\u003eDishDrawers in this range use more than one crockery insert. 512818 is the one supplied with front and back clips. Compare its shape with your broken insert, or check the parts diagram for your model and product code.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547262742606,"sku":"512818","price":49.71,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/512818-genuine-fisher-and-paykel-dishdrawer-crockery-insert-with-front-and-back-clips.jpg?v=1792025512"},{"product_id":"h0120200643-genuine-fisher-and-paykel-long-dishwasher-drain-hose","title":"H0120200643 Genuine Long Dishwasher Drain Hose for Fisher \u0026 Paykel, Haier Dishwashers DW60FC4X1 DW60FC6X1 DW60CHX1 DW60UZ6B HDW13V1S1 HDW15V2S2","description":"\u003cp\u003ePart H0120200643 is the genuine long drain hose for Fisher \u0026amp; Paykel DW60 dishwashers and the matching Haier HDW models. It's listed for the DW60FC4X1 and DW60FC6X1, the DW60FC2W1 and DW60CHX1, and the DW60UZ6B and DW60OUC6X, along with Haier HDW13V1S1, HDW14G2X and HDW15V2S2. The hose carries waste water from the pump to your sink trap or standpipe.\u003c\/p\u003e\n\u003ch2\u003eDishwasher not draining or leaking under the sink\u003c\/h2\u003e\n\u003cp\u003eEvery time the pump runs, dirty water is pushed through this hose and out to the drain. A hose that's kinked behind the cabinet, crushed when the dishwasher was slid into place, or blocked with food scraps leaves water sitting in the base of the tub. You might also see a drain error code, standing water after a cycle or a sour smell. Splits and perished rubber show up as water under the sink or a damp kickboard. If clearing a blockage doesn't fix it, or the hose is damaged, replace it.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine part H0120200643\u003c\/li\u003e\n\u003cli\u003eLong length drain hose\u003c\/li\u003e\n\u003cli\u003eFits Fisher \u0026amp; Paykel DW60 and Haier HDW dishwashers listed\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting the drain hose\u003c\/h2\u003e\n\u003cp\u003eTurn off the power at the wall and the water at the tap, then slide the dishwasher out. Disconnect the old hose at the pump end and at the sink spigot, with a tray ready for leftover water. Route the new hose without kinks and loop it up high under the bench before it drops to the drain, which helps stop dirty water siphoning back. Run a cycle and check both connections.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs this the right drain hose for my dishwasher?\u003c\/h3\u003e\u003cp\u003eCheck the model number on the label, usually on the side edge of the door. H0120200643 is listed for Fisher \u0026amp; Paykel DW60 models such as DW60FC4X1 and DW60CHX1, and Haier HDW13V1S1 and HDW15V2S2.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547263496270,"sku":"H0120200643","price":37.17,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120200643-genuine-fisher-and-paykel-long-dishwasher-drain-hose.jpg?v=1792025781"},{"product_id":"5215dd1001e-genuine-lg-dishwasher-inlet-hose-with-aquastop-220-240v","title":"5215DD1001E Genuine Dishwasher Inlet Hose with Aquastop for LG Dishwashers XD3A15BS XD3A25MB XD4B24PS XD5B14PS XD5B24PS LD-1420T2 LD-1415M1","description":"\u003cp\u003eLG's genuine inlet hose assembly with Aquastop, part 5215DD1001E, feeds water to the dishwasher and cuts the supply off at the tap end if a leak is detected. It replaces 5215DD1001C and several earlier 5215ED1001 and 5215ED1002 numbers. It suits LG XD3A15BS and XD3A25MB, XD4B24PS, and XD5B14PS and XD5B24PS dishwashers, as well as older LD-1415, LD-1420 and LD-1483 models.\u003c\/p\u003e\n\u003ch2\u003eLG dishwasher not filling or showing a leak error\u003c\/h2\u003e\n\u003cp\u003eThe Aquastop hose has an electrically operated valve at the tap end, rated 220-240V. When the dishwasher calls for water the valve opens, and if the inner hose splits, the outer sleeve contains the leak while the safety system shuts the water off. When the valve coil fails or a leak has been detected, the machine won't fill. You might see an inlet or leak error on the display, hear the dishwasher hum without water arriving, or find a damp outer sleeve. Because the valve is built into the hose, the whole assembly is replaced as one.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine LG part 5215DD1001E\u003c\/li\u003e\n\u003cli\u003eInlet hose with Aquastop valve, 220-240V\u003c\/li\u003e\n\u003cli\u003eReplaces 5215DD1001C, 5215ED1001A, 5215ED1002A, 5215ED1002D and 5215ED1002F\u003c\/li\u003e\n\u003cli\u003eFits LG XD and LD series dishwashers listed\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eVoltage\u003c\/th\u003e\n\u003ctd\u003e220-240V\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eReplacing the Aquastop hose\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall and close the tap. The hose's electrical connection is inside the dishwasher, usually reached by removing the kickplate or a side panel. Unplug the old hose's wiring, unscrew it from the tap and the inlet, and fit the new one the same way. Open the tap slowly and check for leaks before restoring power.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWhich LG dishwashers does 5215DD1001E fit?\u003c\/h3\u003e\u003cp\u003eIt's listed for the XD3A15BS and XD3A15NS, the XD3A25MB, the XD4B24PS and XD4B15PS, and the XD5B24PS and XD5B14WH, among other XD models, plus LD series models such as LD-1420T2 and LD-1483T4.\u003c\/p\u003e","brand":"LG","offers":[{"title":"Default Title","offer_id":44547263561806,"sku":"5215DD1001E","price":95.75,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/5215dd1001e-genuine-lg-dishwasher-inlet-hose-with-aquastop-220-240v.jpg?v=1792025514"},{"product_id":"h0120200543c-genuine-fisher-and-paykel-dishwasher-internal-spray-hose","title":"H0120200543C Genuine Dishwasher Internal Spray Hose for Fisher \u0026 Paykel, Haier Dishwashers DW60CHX1 DW60CHW1 DW60CKX1 DW60FC1X1 HDW14G2X HDW15V2S1","description":"\u003cp\u003eH0120200543C is the genuine internal hose that feeds water up to the top sprayer in Fisher \u0026amp; Paykel and Haier dishwashers. It runs inside the tub and carries wash water to the upper spray arm. Models on the list include the Fisher \u0026amp; Paykel DW60CH, DW60CK and DW60FC1 series and the Haier HDW14G2 and HDW15V ranges.\u003c\/p\u003e\n\u003ch2\u003eTop rack coming out dirty? Check the spray hose\u003c\/h2\u003e\n\u003cp\u003eDishwashers like these send water from the wash pump to the lower arm and, through this internal hose, up to the top sprayer. If the hose cracks, splits or comes loose, water escapes before it reaches the top of the tub. The usual result is a top basket that comes out grimy or still has food on it while the bottom rack is clean. You might also hear water spraying in the wrong place, or spot the hose hanging free when you pull the racks out. A hardened or kinked hose cuts the flow in the same way.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine part H0120200543C\u003c\/li\u003e\n\u003cli\u003eInternal top sprayer supply hose\u003c\/li\u003e\n\u003cli\u003eSuits Fisher \u0026amp; Paykel DW60CH, DW60CK and DW60FC1 models\u003c\/li\u003e\n\u003cli\u003eSuits Haier HDW14G2 and HDW15V models\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting the spray hose\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall and turn off the tap. Remove the racks to get clear access inside the tub. Note how the old hose is routed and clipped, as the new one needs to follow the same path so it doesn't catch on the baskets. Push each end fully onto its connector, then run a rinse cycle and check the top rack gets a good spray.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWhere is the model number on my dishwasher?\u003c\/h3\u003e\u003cp\u003eOpen the door and look along the edge of the inner door or the side of the tub for a sticker or plate. Compare that model number with the list for H0120200543C before you order.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547266936910,"sku":"H0120200543C","price":30.89,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120200543c-genuine-fisher-and-paykel-dishwasher-internal-spray-hose.jpg?v=1792025778"},{"product_id":"h0120200377-genuine-fisher-and-paykel-dishwasher-lower-rack-wheel-with-axle-adapter","title":"H0120200377 Genuine Dishwasher Lower Rack Wheel with Axle Adapter for Fisher \u0026 Paykel, Haier Dishwashers DW60FC4X1 DW60FC6X1 DW60CHX1 HDW13V1S1","description":"\u003cp\u003eThe lower basket in Fisher \u0026amp; Paykel and Haier dishwashers rolls on small wheels, and H0120200377 is the genuine replacement wheel. It now comes with an axle adapter. Listed models include the DW60FC and DW60CH series, the DW60U range and the Haier HDW13, HDW14 and HDW15 dishwashers. It's sold as a single wheel, so order one for each wheel that needs replacing.\u003c\/p\u003e\n\u003ch2\u003eLower dishwasher rack dragging or falling off the rails\u003c\/h2\u003e\n\u003cp\u003eEach wheel carries part of the weight of the loaded bottom basket and lets it roll in and out along the door and tub rails. Wheels wear flat, crack or snap off their axles after years of heavy pots and hot water. A rack that drags, tips sideways when you pull it out, jumps off the rail or has an obvious gap where a wheel used to be is the classic sign. Running on a broken wheel can also scratch the door liner. The new wheel is supplied with an axle adapter.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine part H0120200377\u003c\/li\u003e\n\u003cli\u003eLower basket wheel\u003c\/li\u003e\n\u003cli\u003eSupplied with an axle adapter\u003c\/li\u003e\n\u003cli\u003eSold as a single wheel\u003c\/li\u003e\n\u003cli\u003eSuits Fisher \u0026amp; Paykel DW60FC, DW60CH and DW60U models\u003c\/li\u003e\n\u003cli\u003eSuits Haier HDW13, HDW14 and HDW15 models\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eClipping on a new rack wheel\u003c\/h2\u003e\n\u003cp\u003ePull the lower rack out of the dishwasher and turn it upside down on a towel. Remove the broken wheel and any leftover axle pieces. Fit the new wheel with its axle adapter in the same position the old one came from, and spin it to make sure it turns freely. Check the other wheels while the rack is out, as they tend to wear at a similar rate.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eHow many wheels do I need?\u003c\/h3\u003e\u003cp\u003eThis listing is for one wheel with its axle adapter. Count the damaged or missing wheels on your lower rack and order that many. If most of them look worn, replacing the lot at once saves a second job later.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547267690574,"sku":"H0120200377","price":16.26,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120200377-genuine-fisher-and-paykel-dishwasher-lower-rack-wheel-with-axle-adapter.jpg?v=1792025783"},{"product_id":"hc045-generic-dishwasher-drain-hose-1-5m","title":"HC045 Generic Dishwasher Drain Hose 1.5m Universal Replacement Outlet Hose for Dishwashers","description":"\u003cp\u003eHC045 is a generic 1.5m drain hose for dishwashers, a compatible aftermarket part rather than a brand-specific one. It carries waste water from the dishwasher's drain pump outlet to your sink trap or standpipe. Use it to replace an outlet hose that's split, perished or crushed, or when the original won't reach the drain after a move. Check the end fittings against your machine before ordering HC045.\u003c\/p\u003e\n\u003ch2\u003eDishwasher not draining or leaking under the sink?\u003c\/h2\u003e\n\u003cp\u003eEvery time the dishwasher pumps out, dirty water rushes through this hose under pressure. A kink or a crushed section behind the cabinet can slow or stop that flow, leaving water in the bottom of the tub at the end of the cycle. Cracks and splits usually show up as a puddle under the sink or a wet kickboard. Old hoses can also harden and slip off the spigot. If the pump runs but the water won't leave, check the hose and the filter before suspecting the pump itself.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePart number HC045, generic aftermarket hose\u003c\/li\u003e\n\u003cli\u003e1.5m length\u003c\/li\u003e\n\u003cli\u003eDrain hose for dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e1.5m\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFitting a dishwasher drain hose\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off at the wall and close the water tap. Slide the machine out carefully and put towels down, as the old hose will hold some water. Connect the new hose to the pump outlet and secure it with a suitable clamp. Run it to the drain without kinks, with a high loop up under the bench to stop dirty water flowing back. Run a rinse cycle and check for leaks.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWill a 1.5m hose be long enough?\u003c\/h3\u003e\u003cp\u003eMeasure the run from the back of the dishwasher to the sink drain, allowing for the high loop. If your old hose was shorter than 1.5m, this one gives you extra reach. Avoid joining two hoses together if you can.\u003c\/p\u003e","brand":"Universal","offers":[{"title":"Default Title","offer_id":44547267723342,"sku":"HC045_G","price":36.64,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/hc045-generic-dishwasher-drain-hose-1-5m.jpg?v=1792025785"},{"product_id":"524828-genuine-fisher-and-paykel-dishdrawer-drain-filter-assembly","title":"524828 Genuine DishDrawer Drain Filter Assembly for Fisher \u0026 Paykel Dishwashers DD603 DD605I DD60DCX6 DD60DCX7 DD60SCX7 DD90SDFTX2 DS603","description":"\u003cp\u003ePart 524828 is the genuine drain filter assembly for Fisher \u0026amp; Paykel DishDrawer dishwashers. It's the updated version that replaces 523311, 523713 and 529824. The model list covers the DD603 and DD605 families, DD60 single and double drawers in the 6 and 7 series, the DD90 drawers and the DS603 range.\u003c\/p\u003e\n\u003ch2\u003eDishDrawer not draining or leaving grit on dishes\u003c\/h2\u003e\n\u003cp\u003eEach drawer has a drain filter in the bottom of the tub that stops food scraps and grit from reaching the drain pump. Water flows down through it on every cycle. A cracked or warped filter lets debris through, which can jam the pump or end up back on your dishes, while a filter that's missing or badly seated can trigger draining faults. If the drawer is slow to empty, leaves gritty residue or makes a rattling noise from the pump, check this filter first.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 524828\u003c\/li\u003e\n\u003cli\u003eDrain filter assembly, version 2\u003c\/li\u003e\n\u003cli\u003eReplaces 523311, 523713 and 529824\u003c\/li\u003e\n\u003cli\u003eSuits DD603, DD605, DD60, DD90 and DS603 DishDrawers\u003c\/li\u003e\n\u003cli\u003eThe flat filter plate is a separate part\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting the drain filter\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off at the wall before reaching into the tub. Open the drawer, lift out the rack and, on most models, remove the filter plate to expose the drain filter. Lift the old filter out, clean away any debris in the sump below, then seat the new filter firmly. Refit the filter plate and rack, and run a rinse to check it drains.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs this the same as the flat filter plate?\u003c\/h3\u003e\u003cp\u003eNo. 524828 is the drain filter that sits in the bottom of the tub. The flat filter plate is a separate part. If both are damaged, you'll need to order each one.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547268477006,"sku":"524828","price":52.84,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/524828-genuine-fisher-and-paykel-dishdrawer-drain-filter-assembly.jpg?v=1792025517"},{"product_id":"524467-genuine-fisher-and-paykel-dishdrawer-mesh-filter-plate-type-16","title":"524467 Genuine DishDrawer Mesh Filter Plate Type 16 for Fisher \u0026 Paykel Dishwashers DD60DCX9 DD60SCX9 DD60DAX9 DD60DI9 DD60SDFX9 DD60DCW9","description":"\u003cp\u003eThis genuine mesh filter plate, part 524467, is the overmoulded 608 type 16 plate for Fisher \u0026amp; Paykel DishDrawer dishwashers. It's listed for the 8 and 9 series DD60 drawers, including the DD60DCX9 and DD60SCX9, the DD60DAX9, and integrated models like the DD60DI9, plus white versions such as the DD60DCW9.\u003c\/p\u003e\n\u003ch2\u003eFood scraps getting through to the DishDrawer pump\u003c\/h2\u003e\n\u003cp\u003eThe filter plate covers the bottom of the drawer and catches food particles from the wash water before it's pumped back through the spray arm. Its fine mesh keeps grit off your dishes and protects the pump. When the mesh tears, the plate warps or the overmoulded edge breaks away, debris goes straight through. You'll notice gritty dishes, food left on glasses, a drawer that drains slowly or a noisier pump. Rinse the plate regularly and replace it once it's damaged.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 524467\u003c\/li\u003e\n\u003cli\u003eMesh filter plate, overmoulded 608 type 16\u003c\/li\u003e\n\u003cli\u003eSuits DD60 8 and 9 series DishDrawers\u003c\/li\u003e\n\u003cli\u003eThe micro filter is a separate part\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eOvermoulded 608 Type 16\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eSwapping the filter plate\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off at the wall. Open the drawer and lift out the basket so you can see the base of the tub, removing the spray arm first if it's in the way. Take out the old plate, clean the area underneath and check the micro filter for damage while it's exposed. Lay the new plate in place so it sits flat with no gaps around the edge, then refit the parts and run a rinse.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eHow do I know if I need type 16?\u003c\/h3\u003e\u003cp\u003eMatch your model number against the list for 524467. Type 16 suits the DD60 8 and 9 series, such as the DD60DCX9 and DD60SCX9. Older drawers use different plates, so don't go by appearance alone.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547275456590,"sku":"524467","price":109.31,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/524467-genuine-fisher-and-paykel-dishdrawer-mesh-filter-plate-type-16.jpg?v=1792025515"},{"product_id":"525067-genuine-fisher-and-paykel-dishdrawer-double-drain-hose-y-connector","title":"525067 Genuine Double Drain Hose Y Connector for Fisher \u0026 Paykel DishDrawer Dishwashers DD603 DD605 DD60DCX6 DD60DCX7 DD60DCX9 DD60DI7 DD60DAX9","description":"\u003cp\u003eDouble DishDrawers have two drain hoses, and 525067 is the genuine Y connector that joins them before they reach the drain. It's listed for Fisher \u0026amp; Paykel double drawer models, from the DD603 and DD605 through to the DD60DCX6 and DD60DCX7, the DD60DCX9 and DD60DAX9, and integrated models such as the DD60DI7.\u003c\/p\u003e\n\u003ch2\u003eWater leaking under a double DishDrawer\u003c\/h2\u003e\n\u003cp\u003eBoth drawers pump their waste water through their own hose, and this Y connector merges them into a single line to the household drain. If the connector cracks or a hose end lets go, dirty water escapes every time either drawer drains. Look for water on the floor of the cabinet next to the dishwasher, a damp kick panel or a smell of stale water. A blocked connector can also stop one or both drawers from draining properly, leaving water sitting in the bottom of the tub.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 525067\u003c\/li\u003e\n\u003cli\u003eDouble drain spigot connector, Y shape\u003c\/li\u003e\n\u003cli\u003eJoins the drain hoses of both drawers\u003c\/li\u003e\n\u003cli\u003eSuits double DishDrawer models in the DD60 range\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting the Y connector\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall and have a towel ready, as the hoses will hold some water. Note which hose goes to which leg of the connector, then release any clamps and pull the old connector out. Push the hoses fully onto the new connector, refit the clamps and run each drawer through a rinse to check for leaks at every joint.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDo I need this connector for a single DishDrawer?\u003c\/h3\u003e\u003cp\u003eNo. This connector is for double DishDrawer installs, where two drain hoses need to join into one. Single drawer models have one drain hose and don't use it.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547275554894,"sku":"525067","price":25.67,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/525067-genuine-fisher-and-paykel-dishdrawer-double-drain-hose-y-connector.jpg?v=1792025517"},{"product_id":"140003571019-genuine-dishlex-dishwasher-drain-hose-2-23m","title":"140003571019 Genuine Dishwasher Drain Hose 2.23m for Dishlex, Electrolux, Westinghouse, Simpson, AEG Dishwashers ESF65060W ESL4143 DX100FWW","description":"\u003cp\u003eAt 2.23m long, part 140003571019 is the genuine drain hose for a wide range of Dishlex, Electrolux, Westinghouse, Simpson and AEG dishwashers. It replaces 673000900039, 1526492010 and 1560330-10\/0. More than 400 models are listed, including the ESF65060W and ESF66060X, the ESL4143, the DX100FWW, the EX302WJ and the AEG F77000W0P.\u003c\/p\u003e\n\u003ch2\u003eDishwasher not draining or leaking from the drain hose\u003c\/h2\u003e\n\u003cp\u003eThe drain hose carries waste water from the pump to the sink trap or standpipe. Because it runs behind cabinets, it's easily crushed, kinked or nicked when the dishwasher is pushed back in. A damaged hose leaks onto the floor under the machine, while a kinked or partly blocked one leaves dirty water sitting in the bottom of the tub at the end of the cycle. Food sludge can also build up inside older hoses. If the pump runs but the water goes nowhere, check the hose before suspecting the pump.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Electrolux group part 140003571019\u003c\/li\u003e\n\u003cli\u003eDrain hose, 2.23m long\u003c\/li\u003e\n\u003cli\u003eReplaces 673000900039, 1526492010 and 1560330-10\/0\u003c\/li\u003e\n\u003cli\u003eSuits Dishlex, Electrolux, Westinghouse, Simpson and AEG dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e2.23m\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eReplacing the drain hose\u003c\/h2\u003e\n\u003cp\u003eSwitch off at the wall and turn off the water tap before sliding the dishwasher out. Put a tray and towels down, as the old hose will hold dirty water. Disconnect it at the sink waste and at the pump, then fit the new hose, routing it so it rises to the height recommended in your installation manual before dropping to the drain. Secure both ends and run a rinse to check for leaks.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eCan I extend the hose if 2.23m isn't long enough?\u003c\/h3\u003e\u003cp\u003eIdeally the hose should reach without an extension. If you must extend it, use a proper joiner, secure both joints, and keep the total run within the limit in your dishwasher's installation manual.\u003c\/p\u003e","brand":"Electrolux","offers":[{"title":"Default Title","offer_id":44547276406862,"sku":"140003571019","price":54.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/140003571019-genuine-dishlex-dishwasher-drain-hose-2-23m.jpg?v=1792025690"},{"product_id":"hc047-generic-dishwasher-drain-hose-2-5m","title":"HC047 Generic Dishwasher Drain Hose 2.5m Long Universal Dishwasher Outlet Hose Part","description":"\u003cp\u003eHC047 is a generic 2.5 metre drain hose for dishwashers, sold as a universal replacement. It carries waste water from the dishwasher's pump to your sink waste or standpipe. The extra length helps when a dishwasher is moving to a new spot or the original hose won't quite reach. Compare both ends with your current hose before ordering, as connections vary between brands.\u003c\/p\u003e\n\u003ch2\u003eDishwasher not draining or leaking underneath? Check the drain hose\u003c\/h2\u003e\n\u003cp\u003eEvery cycle, the drain pump pushes dirty water out through this hose, so it has to stay clear, sealed and free of sharp bends. Hoses split with age, get crushed behind cabinets or kink when the machine is pushed back into its space. Typical signs are water left in the bottom of the tub at the end of a wash, slow emptying, or puddles under the kitchen bench. A hose that's too short can also pull off its spigot. Swapping it for a longer, undamaged hose is a cheap fix.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePart number HC047, generic universal hose\u003c\/li\u003e\n\u003cli\u003e2.5m length\u003c\/li\u003e\n\u003cli\u003eCarries waste water from the pump to the sink waste or standpipe\u003c\/li\u003e\n\u003cli\u003eHandy where the original hose is too short\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e2.5m\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eReplacing a dishwasher drain hose\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off at the wall and close the tap before pulling it out. Keep a towel and a shallow tray handy, as some water will run out of the old hose. Fit the new hose with a secure clamp at the pump end, run it without kinks, and loop it up high before it reaches the sink waste so dirty water can't siphon back. Run a short cycle and check for leaks.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWill this hose fit my dishwasher?\u003c\/h3\u003e\u003cp\u003eHC047 is a universal hose, so it suits many dishwashers, but end fittings differ between brands. Measure the spigot on your pump outlet and compare the old hose's ends before buying. You may also need clamps to secure it.\u003c\/p\u003e","brand":"Universal","offers":[{"title":"Default Title","offer_id":44547277914190,"sku":"HC047_G","price":36.64,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/hc047-generic-dishwasher-drain-hose-2-5m.jpg?v=1792025784"},{"product_id":"524888-genuine-fisher-and-paykel-dishdrawer-filter-plate-kit","title":"524888 Genuine DishDrawer Filter Plate Kit for Fisher \u0026 Paykel Dishwashers DD60DCX7 DD60DCW7 DD60SCW7 DD60DI7 DD60SI7 DD605, Replaces 529822P","description":"\u003cp\u003eFisher \u0026amp; Paykel kit 524888 is the genuine filter plate for DishDrawer dishwashers. It's listed for the DD60DCX7 and DD60DCW7, the DD60SCW7, the DD60DI7 and DD60SI7, and the DD605. Earlier numbers 529822P and 523381 are linked to this kit, so if either appears on an old invoice or parts list, 524888 is the one to order.\u003c\/p\u003e\n\u003ch2\u003eDishDrawer leaving food and grit on dishes\u003c\/h2\u003e\n\u003cp\u003eThe filter plate sits in the base of each drawer's tub and screens the wash water before the pump sends it back through the spray arm. It stops food scraps from circulating and catches the grit that would otherwise end up on clean dishes. A plate that's cracked, warped or not sitting flat lets debris slip past, so you'll see gritty residue on glasses, food specks on plates and a smelly tub. A blocked or damaged plate can also leave dirty water sitting in the bottom of the drawer after a wash.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 524888\u003c\/li\u003e\n\u003cli\u003eFilter plate kit for DishDrawer dishwashers\u003c\/li\u003e\n\u003cli\u003eLinked numbers 529822P and 523381\u003c\/li\u003e\n\u003cli\u003eListed for DD60DCX7, DD60DCW7, DD60SCW7, DD60DI7, DD60SI7 and DD605\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eChanging the DishDrawer filter plate\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off at the wall and open the drawer. Lift out the basket. Depending on the model, the spray arm and filter may need to come out before you can reach the plate in the base of the tub. Note how the old plate locates before lifting it out. Clean any build-up from the sump area while it's open, fit the new plate so it sits flat, refit the other parts and run a rinse to check everything drains.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs this the same as 529822P?\u003c\/h3\u003e\u003cp\u003e529822P and 523381 are both linked to this kit. If your old invoice or parts list shows one of those numbers, 524888 is the part to order. Check your DishDrawer model number against the list as well.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547300786254,"sku":"524888","price":193.98,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/524888-genuine-fisher-and-paykel-dishdrawer-filter-plate-kit.jpg?v=1792025518"},{"product_id":"h0120200366-genuine-fisher-and-paykel-dishwasher-lower-spray-arm","title":"H0120200366 Genuine Lower Spray Arm for Fisher \u0026 Paykel, Haier Dishwashers DW60FC4X1 DW60FC6X1 DW60CHX1 DW60UC6X HDW13V1S1 HDW15V2S2","description":"\u003cp\u003eH0120200366 is a genuine lower spray arm shared by a number of Fisher \u0026amp; Paykel and Haier dishwasher models. On the Fisher \u0026amp; Paykel side it's listed for the DW60FC4X1, the DW60FC6X1 and DW60FC2X1, the DW60CHX1 and DW60CKX1, plus the DW60UC6X and DW60UD6X1. Haier models include the HDW15V2S2, the HDW15G3X and the HDW13V1S1. It spins under the bottom basket and does most of the work on plates and pots.\u003c\/p\u003e\n\u003ch2\u003eDishes on the bottom rack coming out dirty\u003c\/h2\u003e\n\u003cp\u003eWater from the wash pump is forced up into the lower arm and out through its jets, and the force of that water spins the arm under the bottom basket. If the arm cracks or warps, pressure leaks away and it slows or stops turning. Blocked jets have the same effect. You'll notice food left on plates in the lower rack, gritty residue on pots, or a knocking sound where a loose arm catches on the basket. Clear the jets with a toothpick first. If the arm is split, warped or won't spin freely on its mount, replace it.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine part H0120200366\u003c\/li\u003e\n\u003cli\u003eLower spray arm\u003c\/li\u003e\n\u003cli\u003eListed for Fisher \u0026amp; Paykel DW60 dishwashers\u003c\/li\u003e\n\u003cli\u003eAlso listed for Haier HDW13 and HDW15 dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eRemoving the lower spray arm\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off and pull the bottom basket right out. Depending on the model, the lower arm either lifts straight up off its hub or is held by a nut or clip in the centre, so check before pulling hard. Rinse the hub and filter area while the arm is off. Press the new arm into place, spin it by hand to make sure it clears the filter and basket, then run a quick program.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eHow can I tell if my spray arm is blocked or broken?\u003c\/h3\u003e\u003cp\u003eTake it out and look along each jet. Blocked holes can be cleared with a toothpick under running water. A crack, warping or a loose seam means the arm won't hold pressure, and it needs replacing.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547307634766,"sku":"H0120200366","price":43.44,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120200366-genuine-fisher-and-paykel-dishwasher-lower-spray-arm.jpg?v=1792025777"},{"product_id":"agb74152501-genuine-lg-dishwasher-upper-spray-arm-nozzle-assembly","title":"AGB74152501 Genuine Upper Spray Arm Nozzle Assembly for LG Dishwashers XD3A15BS XD3A25MB XD4B24PS XD5B14PS XD5B24PS XD3A15NS XD4B15PS","description":"\u003cp\u003eLG lists this upper spray arm as a nozzle assembly, part AGB74152501. It's a genuine LG part for the XD3A15BS and XD3A15MB, the XD3A25MB and XD3A25PS, the XD4B24PS, the XD4B15PS and XD4B14PS, and the XD5B24PS along with the XD5B14PS. The number AGB74152502 is also linked to it, so either number on your old arm or paperwork leads to this part.\u003c\/p\u003e\n\u003ch2\u003eTop rack of the LG dishwasher not cleaning\u003c\/h2\u003e\n\u003cp\u003eThe upper arm spins beneath the top basket and sprays the glasses, cups and bowls loaded there. Water reaches it through a feed pipe from the wash pump, and the jets are angled so the water pressure turns the arm. If the arm is cracked, its jets are blocked by food or scale, or it no longer turns freely on its mount, the top rack misses out. You'll see cloudy or spotty glasses, food left inside bowls and mugs, and one area of the basket coming out dirtier than the rest.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine LG part AGB74152501\u003c\/li\u003e\n\u003cli\u003eUpper spray arm nozzle assembly\u003c\/li\u003e\n\u003cli\u003eAlso linked to AGB74152502\u003c\/li\u003e\n\u003cli\u003eListed for LG XD3, XD4 and XD5 dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSwapping the upper spray arm\u003c\/h2\u003e\n\u003cp\u003eTurn off the dishwasher and slide the upper basket out. The arm is attached to the underside of the basket, usually held by a nut or a twist lock in the centre. Release it, check the feed tube and docking point for debris, and clean them out. Fit the new arm, lock it on and turn it by hand to check it spins without hitting anything. Reload the basket and run a short program.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs AGB74152502 the same as AGB74152501?\u003c\/h3\u003e\u003cp\u003eAGB74152502 is linked to this spray arm in LG parts listings, so either number points to the same upper arm here. Still check your dishwasher's model number, usually on a label on the side of the door, against the list before ordering.\u003c\/p\u003e","brand":"LG","offers":[{"title":"Default Title","offer_id":44547329982542,"sku":"AGB74152501","price":34.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/agb74152501-genuine-lg-dishwasher-upper-spray-arm-nozzle-assembly.jpg?v=1792025748"},{"product_id":"529855-genuine-fisher-and-paykel-dishdrawer-inlet-hose-1-9m","title":"529855 Genuine DishDrawer Inlet Hose 1.9m for Fisher \u0026 Paykel Dishwashers DD60DCX9 DD60SCX9 DD60DCX7 DD60DI7 DD605 DD90SDFTX2 DD60SCTX7","description":"\u003cp\u003ePart 529855 is a genuine 1.9m inlet hose for Fisher \u0026amp; Paykel DishDrawer dishwashers. With more than a hundred models on file, it covers the DD605 and DD603I, the DD60DCX9 and DD60SCX9, the DD60DCX7 and DD60SCTX7, the DD60DI7, DD60SI9 and DD60SLI9, and the DD90SDFTX2. It runs from the water tap to the dishwasher's inlet connection.\u003c\/p\u003e\n\u003ch2\u003eWater on the floor near the dishwasher\u003c\/h2\u003e\n\u003cp\u003eThe inlet hose carries water from the tap to the dishwasher's fill valve each time a drawer fills. It sits under pressure in a tight space, so age, heat and being squashed behind the cabinetry all take their toll. Warning signs include a damp floor or cupboard base, drips at the tap or the hose connection, bulges or cracking in the outer cover, and drawers that fill slowly because the hose is kinked. A split inlet hose can release a lot of water quickly, so replace one that looks tired before it fails.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 529855\u003c\/li\u003e\n\u003cli\u003eDishDrawer inlet hose, 1.9m long\u003c\/li\u003e\n\u003cli\u003eListed for DD60, DD603 and DD605 DishDrawer models\u003c\/li\u003e\n\u003cli\u003eAlso listed for DD90 DishDrawer models\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e1.9m\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eChanging the inlet hose\u003c\/h2\u003e\n\u003cp\u003eTurn off the tap and switch the dishwasher off at the wall. Reaching the connection at the dishwasher end usually means removing the toe kick or sliding the unit out, so check your installation guide. Make sure the sealing washers are in place, tighten the fittings by hand and then a little more, and avoid sharp bends when routing the hose. Turn the tap on slowly and check both ends for drips before running a wash.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eShould I replace the hose if it isn't leaking yet?\u003c\/h3\u003e\u003cp\u003eIf it's cracked, bulging, stiff or kinked, yes. An inlet hose is under mains pressure whenever the tap is on, so a worn one can burst without warning. Turning the tap off when you go away for a while also reduces the risk.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547331489870,"sku":"529855","price":42.39,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/529855-genuine-fisher-and-paykel-dishdrawer-inlet-hose-1-9m.jpg?v=1792025516"},{"product_id":"140000554083-genuine-electrolux-water-level-pressure-switch","title":"140000554083 Genuine Water Level Pressure Switch for Electrolux Group Dishwashers, Also Catalogued as A00055408","description":"\u003cp\u003ePart 140000554083 is a genuine Electrolux water level pressure switch, also catalogued as A00055408. Listings for A00055408 describe it as a dishwasher pressure switch for Electrolux built machines. There's no confirmed model list on file, so check that your old switch or your model's parts list shows 140000554083 or A00055408 before you order.\u003c\/p\u003e\n\u003ch2\u003eDishwasher overfilling or not filling? How the pressure switch works\u003c\/h2\u003e\n\u003cp\u003eA pressure switch measures the water level by sensing air pressure in a small chamber or tube connected to the sump. As water comes in, the pressure rises until the switch changes over and tells the control to stop filling. When the switch sticks, or its tube is blocked or split, the machine can overfill and leak, stop filling too early, or sit at the start of a program waiting for water. Check the pressure tube for kinks or debris before replacing the switch.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Electrolux part number 140000554083\u003c\/li\u003e\n\u003cli\u003eAlso catalogued as A00055408\u003c\/li\u003e\n\u003cli\u003eWater level pressure switch\u003c\/li\u003e\n\u003cli\u003eReplaces a stuck or faulty level switch\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eReplacing the pressure switch\u003c\/h2\u003e\n\u003cp\u003eSwitch off at the wall and turn off the water tap before pulling the machine out. Photograph the wiring plug and terminals, and note how the pressure tube connects. Fit the new switch, then reconnect the tube so it's free of kinks and low sags where water could sit, and secure it with its clip. Run a program and watch that it fills to the normal level and stops.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWhere do I find my dishwasher's model number?\u003c\/h3\u003e\u003cp\u003eIt's printed on the rating label, usually on the side or top edge of the inner door. Use the model number and the PNC shown there to check the parts list for 140000554083 or A00055408.\u003c\/p\u003e","brand":"Electrolux","offers":[{"title":"Default Title","offer_id":44547338928206,"sku":"140000554083","price":54.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/140000554083-genuine-electrolux-water-level-pressure-switch.jpg?v=1792025689"},{"product_id":"512484p-genuine-fisher-and-paykel-dishdrawer-door-handle-kit-double-silver-stainless","title":"512484P Genuine DishDrawer Door Handle Kit, Double, Stainless for Fisher \u0026 Paykel Dishwashers DD60DCX6 DD60DCX7 DD60SCX6 DD60SCX7 DD60SCTX7","description":"\u003cp\u003eFisher \u0026amp; Paykel part 512484P is a genuine door handle kit for DishDrawer dishwashers, catalogued as a double kit in a silver stainless finish. It's listed for the DD60DCX7 and DD60DCX6, the DD60SCX7 and DD60SCX6, and the DD60SCTX7 and DD60SCTX6. The numbers 522896 and 510692 are also linked to this handle, so either one on an old order points to the same part.\u003c\/p\u003e\n\u003ch2\u003eLoose, broken or worn DishDrawer handle\u003c\/h2\u003e\n\u003cp\u003eEach DishDrawer is opened by pulling on its handle, so the handle and its fixings take a fair bit of force every day. Over the years the handle can work loose, crack at a mounting point, or lose its finish where hands grip it. A wobbly handle makes the drawer awkward to open and can put strain on the drawer front. If the handle has snapped off or the mounting points are broken, a new kit is the clean fix. On a double model, fitting new handles to both drawers keeps the front looking even.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 512484P\u003c\/li\u003e\n\u003cli\u003eDouble handle kit, silver stainless finish\u003c\/li\u003e\n\u003cli\u003eLinked numbers 522896 and 510692\u003c\/li\u003e\n\u003cli\u003eListed for DD60DCX6, DD60DCX7, DD60SCX6, DD60SCX7, DD60SCTX6 and DD60SCTX7\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eFinish\u003c\/th\u003e\n\u003ctd\u003eSilver stainless\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFitting the new handle\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall first. Open the drawer and check how the old handle is fixed, as the screws are usually reached from inside the drawer front, which may mean removing the inner panel. Support the handle while you undo the fixings, then fit the new one and tighten the screws evenly so it sits straight. Don't overtighten into plastic mounts.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eHow many handles are in the kit?\u003c\/h3\u003e\u003cp\u003eIt's catalogued as a double kit. If you need to know exactly what's in the pack for your model, contact us before ordering and we'll confirm it.\u003c\/p\u003e\n\u003ch3\u003eWill it fit my single drawer model?\u003c\/h3\u003e\u003cp\u003eIt's listed for the single drawer DD60SCX6, DD60SCX7, DD60SCTX6 and DD60SCTX7 as well as the double DD60DCX6 and DD60DCX7. Check that the model on your compliance label matches one of these.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547341811790,"sku":"512484P","price":180.39,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/512484p-genuine-fisher-and-paykel-dishdrawer-door-handle-kit-double-silver-stainless.jpg?v=1792025509"},{"product_id":"690074493-generic-dishwasher-door-lock-and-spacer-kit","title":"690074493 Generic Door Lock and Spacer Kit suits Smeg Dishwashers DWA6214X DWA6314X DWAU6214X DWAU6314X DWAU6315X DWA6314B DWA6214W","description":"\u003cp\u003eMade to suit Smeg part 690074493, this generic kit includes a dishwasher door lock and the spacer that goes with it. It's listed for the DWA6314X and DWA6314B, the DWA6214X, DWA6214W and DWA6214S, and the DWAU6314X, DWAU6214X and DWAU6315X, plus the DWAU6D15XT. Smeg numbers 697690348, 697690335 and 697690342 are linked to the same lock.\u003c\/p\u003e\n\u003ch2\u003eSmeg dishwasher won't start or door won't stay shut\u003c\/h2\u003e\n\u003cp\u003eThe door lock does two jobs. It holds the door shut against the tub seal, and its switch tells the control that the door is closed so a program can start. When the latch wears or the switch fails, the dishwasher may not start at all, may beep or flash when you press start, or may stop partway through a wash. Some faulty locks won't catch, so the door falls open, while others catch but the machine still acts as though the door is open. A broken plastic hook or a door that needs slamming to latch are other giveaways.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGeneric replacement to suit Smeg part 690074493\u003c\/li\u003e\n\u003cli\u003eDoor lock with spacer\u003c\/li\u003e\n\u003cli\u003eLinked numbers 697690348, 697690335 and 697690342\u003c\/li\u003e\n\u003cli\u003eListed for Smeg DWA and DWAU dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eReplacing the door lock\u003c\/h2\u003e\n\u003cp\u003eUnplug the dishwasher or switch it off at the wall. The lock is usually mounted in the top of the inner door, so you'll need to remove the outer door panel or the control panel to reach it. Photograph the wiring before unplugging the connector. Fit the new lock with the spacer positioned the same way as before, reconnect the wiring and check the door latches with a firm click before running a test program.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDoes the kit include the spacer?\u003c\/h3\u003e\u003cp\u003eYes. It's a door lock and spacer kit, so the spacer comes with the lock. Fit it the way the old one was set up so the latch lines up with the strike on the tub.\u003c\/p\u003e","brand":"Universal","offers":[{"title":"Default Title","offer_id":44547345711182,"sku":"690074493_G","price":99.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/690074493-generic-dishwasher-door-lock-and-spacer-kit.jpg?v=1792025592"},{"product_id":"140005633064-genuine-aeg-dishwasher-drain-hose-2340mm","title":"140005633064 Genuine Dishwasher Drain Hose 2340mm for AEG, Dishlex, Electrolux, Westinghouse Dishwashers FFE83800PM DSF6106X ESF8735ROX","description":"\u003cp\u003eElectrolux group part 140005633064 is a genuine 2340mm drain hose used across AEG, Dishlex, Electrolux and Westinghouse dishwashers. AEG models on file are the FFE83800PM and FEE83700PM, the FFB72600PM and FFB72600PW, and the FFE72730PM. It also suits the Dishlex DSF6106X, DSF6106W and DSF6105X, and the Electrolux ESF8735ROX. It's catalogued as 140010997017 as well.\u003c\/p\u003e\n\u003ch2\u003eDishwasher not draining or leaking from the back\u003c\/h2\u003e\n\u003cp\u003eWaste water leaves the dishwasher through this hose, pushed by the drain pump up to the sink spigot or standpipe. Hoses get kinked when the machine is pushed back into the cabinet, pinched by cupboard fittings, or split where they rub on a sharp edge. A kink or blockage leaves dirty water in the tub at the end of a cycle and can trigger a drain error, while a split hose leaks into the cabinet or onto the floor during the pump out. Check the hose along its full length and flush water through it to find any blockage before replacing it.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Electrolux group part 140005633064\u003c\/li\u003e\n\u003cli\u003eDrain hose, 2340mm long\u003c\/li\u003e\n\u003cli\u003eAlso catalogued as 140010997017\u003c\/li\u003e\n\u003cli\u003eListed for AEG, Dishlex and Electrolux dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e2340mm\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFitting the drain hose\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off at the wall and turn off the tap. Slide the machine out and have a bucket and towel ready for the water left in the hose and sump. Connect the new hose at the dishwasher end first, then route it up to the sink spigot with a high loop so dirty water can't siphon back. Clamp it securely, push the machine back without pinching the hose and run a short program to test.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eCan I join an extension to make it longer?\u003c\/h3\u003e\u003cp\u003eIt's better to use one continuous hose. This one is 2340mm long, and joins add extra points where leaks or blockages can start. If your sink outlet is further away, check your installation manual for the maximum drain hose length.\u003c\/p\u003e","brand":"Electrolux","offers":[{"title":"Default Title","offer_id":44547349446734,"sku":"140005633064","price":45.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/140005633064-genuine-aeg-dishwasher-drain-hose-2340mm.jpg?v=1792025691"},{"product_id":"50286965004-genuine-dishlex-dishwasher-lower-basket-wheel-kit-8-pieces","title":"50286965004 Genuine Lower Basket Wheel Kit, 8 Pieces for Dishlex, Electrolux, Simpson, Westinghouse Dishwashers DX303SK ESF63020 ESF65010","description":"\u003cp\u003ePart 50286965004 is a genuine kit of eight wheels for the lower basket of Dishlex, Electrolux, Simpson and Westinghouse dishwashers. More than 200 models are on file, from the Dishlex DX303SK and DX203WK to Electrolux ESF63020, ESF64010 and ESF65010 versions, along with older machines such as the ESF6146 and ESF4160. It's also catalogued as 911516028 and 50286965-00\/4.\u003c\/p\u003e\n\u003ch2\u003eDishwasher bottom basket dragging or falling off\u003c\/h2\u003e\n\u003cp\u003eThe lower basket rolls on small wheels that run along the tub rails. Heat, detergent and the weight of a full load wear them down, and over time they crack, flatten, seize on their axles or snap off altogether. Then the basket jerks or grinds as you pull it out, tips forward, jumps off the rails or scrapes the door. A missing wheel also lets the basket sit crooked, which can stop the lower spray arm turning freely. Eight wheels come in the kit, so there are plenty to replace all the worn ones together.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Electrolux group part 50286965004\u003c\/li\u003e\n\u003cli\u003eKit of 8 lower basket wheels\u003c\/li\u003e\n\u003cli\u003eAlso catalogued as 911516028 and 50286965-00\/4\u003c\/li\u003e\n\u003cli\u003eListed for Dishlex DX and Electrolux ESF dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003ePieces\u003c\/th\u003e\n\u003ctd\u003e8\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFitting the basket wheels\u003c\/h2\u003e\n\u003cp\u003eMake sure the dishwasher is off and cool before you start. Pull the lower basket out and turn it upside down on a towel. Most wheels unclip from their holders or slide off a short axle, so remove one and note how it sits before doing the rest. Press the new wheels on until they seat fully, check each one spins freely, and slide the basket back onto the rails.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eHow many wheels does my basket use?\u003c\/h3\u003e\u003cp\u003eThat varies by model, so count the wheels on your lower basket before ordering. This kit has eight, which lets you replace every one that's cracked, flat or stiff in a single job.\u003c\/p\u003e","brand":"Electrolux","offers":[{"title":"Default Title","offer_id":44547353444430,"sku":"50286965004","price":40.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/50286965004-genuine-dishlex-dishwasher-lower-basket-wheel-kit-8-pieces.jpg?v=1792025690"},{"product_id":"h0120802868b-genuine-fisher-and-paykel-dishdrawer-cutlery-basket","title":"H0120802868B Genuine DishDrawer Cutlery Basket for Fisher \u0026 Paykel Dishwashers DD60DCX6 DD60SCX6 DD60DI6 DD60SI6 DD60SCTX6 DD90SDFTX2","description":"\u003cp\u003eBroken the cutlery basket in your Fisher \u0026amp; Paykel DishDrawer? H0120802868B is the genuine replacement. Older F\u0026amp;P paperwork lists the same basket as 522629. It suits DD60 drawers with model numbers ending in 6, such as DD60DCX6, DD60SCW6, DD60DI6 and DD60SI6, plus the DD90SDFTX and DD90STI models. Order it when the old basket has snapped handles, a split grid or pieces missing.\u003c\/p\u003e\n\u003ch2\u003eWhen to replace a DishDrawer cutlery basket\u003c\/h2\u003e\n\u003cp\u003eThe cutlery basket keeps knives, forks and spoons standing apart in the drawer so the spray can reach every surface and pieces don't nest together. Years of hot washes make the plastic brittle. Handles snap, the grid cracks and cutlery starts slipping through onto the wash system underneath, where it can stop the spray arm turning or sit on the filter. Spoons lying loose in the bottom of the drawer, rattling during the cycle, or cutlery coming out with food still stuck to it all point to a worn basket.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part H0120802868B\u003c\/li\u003e\n\u003cli\u003eOlder F\u0026amp;P number 522629\u003c\/li\u003e\n\u003cli\u003eSuits DD60 DishDrawer models ending in 6, e.g. DD60DCX6 and DD60SCTX6\u003c\/li\u003e\n\u003cli\u003eAlso listed for DD90SDFTM, DD90SDFTX and DD90STI models\u003c\/li\u003e\n\u003cli\u003eLifts in and out of the drawer, no tools required\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSwapping the basket over\u003c\/h2\u003e\n\u003cp\u003eThere's nothing to undo. Open the drawer all the way, lift the old basket out and set the new one in its place, making sure it sits flat. Turn the spray arm by hand afterwards to check nothing fouls it. Unsure which DishDrawer you have? Your user guide shows where the product label sits, and the model number on it should match one of the models for this basket.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs this the same basket as 522629?\u003c\/h3\u003e\u003cp\u003eYes. 522629 is the older Fisher \u0026amp; Paykel part number for this cutlery basket, and H0120802868B is the current genuine number. Both refer to the basket used in the DD60 and DD90 DishDrawer models on this page.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547365994574,"sku":"H0120802868B","price":46.58,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120802868b-genuine-fisher-and-paykel-dishdrawer-cutlery-basket.jpg?v=1792025782"},{"product_id":"hc046-generic-dishwasher-drain-hose-1-5m-with-90-degree-elbow","title":"HC046 Generic Dishwasher Drain Hose 1.5m with 90 Degree Elbow End Universal Dishwasher Outlet Hose Part","description":"\u003cp\u003eNeed a shorter replacement drain hose? HC046 is a generic 1.5m dishwasher outlet hose with a 90 degree elbow on one end. The elbow lets the hose make a tight turn without kinking, which helps where the dishwasher sits close to the sink cabinet. It's a universal part, so compare the end connections and diameter with your old hose before ordering.\u003c\/p\u003e\n\u003ch2\u003eWater left in the dishwasher? A damaged drain hose could be why\u003c\/h2\u003e\n\u003cp\u003eDirty water leaves the dishwasher through the drain hose each time the pump runs. Because the hose sits out of sight behind the machine, damage often goes unnoticed until there's a problem. Splits cause leaks under the cabinet, while kinks and crushed sections slow drainage and can leave water in the bottom of the tub. A hose that has hardened and cracked near the pump connection is another common failure. A 90 degree elbow end can take the strain out of the tight bend that causes many of these kinks.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003ePart number HC046, generic universal hose\u003c\/li\u003e\n\u003cli\u003e1.5m length\u003c\/li\u003e\n\u003cli\u003eOne 90 degree elbow end\u003c\/li\u003e\n\u003cli\u003eSuits installs where the outlet hose has to make a tight turn\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e1.5m\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eEnd fitting\u003c\/th\u003e\n\u003ctd\u003eOne 90 degree elbow\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFitting a drain hose with an elbow end\u003c\/h2\u003e\n\u003cp\u003eIsolate the dishwasher at the power point and shut the water tap. Pull the machine out gently so you don't stretch the hoses. Undo the clamp at the pump outlet and catch the water that runs out. Fit the new hose, clamp it securely, then route it so the elbow takes the tightest bend. Fix the outlet end up high at the sink waste or standpipe and test for leaks.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs 1.5m long enough for my kitchen?\u003c\/h3\u003e\u003cp\u003eMeasure the path from the back of the dishwasher to the sink waste or standpipe, allowing extra for a high loop. If you need more than 1.5m, the 2.5m hose HC047 may suit better.\u003c\/p\u003e","brand":"Universal","offers":[{"title":"Default Title","offer_id":44547367370830,"sku":"HC046_G","price":39.6,"currency_code":"AUD","in_stock":true}]},{"product_id":"522085-genuine-fisher-and-paykel-dishdrawer-lid-actuator-kit-pack-of-2","title":"522085 Genuine DishDrawer Lid Actuator Kit Pack of 2 for Fisher \u0026 Paykel Dishwashers DD60DCX6 DD60SCX7 DD605 DS605 DD60DCX9 DD90SDFTX2","description":"\u003cp\u003eFisher \u0026amp; Paykel part 522085 is a genuine kit of two lid actuators for DishDrawer dishwashers. The lid is the panel that comes down onto the wash tub to seal it while the drawer runs, and these actuators move it. The kit is listed for the DD605 and DS605 drawers, DD60 models ending in 6, 7 and 9, and the DD90SDFTX and DD90STI. Wiring isn't included, so your existing connections are reused.\u003c\/p\u003e\n\u003ch2\u003eDishDrawer leaking or the lid not sealing\u003c\/h2\u003e\n\u003cp\u003eEach drawer has a lid in the top of the cabinet that seals the tub during the wash. At the start of a cycle the actuators lower the lid onto the tub, and at the end they release it so the drawer can open. When an actuator weakens or fails, the lid doesn't clamp down evenly. Water can escape over the tub edge, the drawer may leak onto the floor or into the drawer below, and the cycle may stop with a fault. Fitting both actuators from the kit at once keeps the lid pulling down evenly.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 522085\u003c\/li\u003e\n\u003cli\u003ePack of 2 lid actuators\u003c\/li\u003e\n\u003cli\u003eWiring not included, the existing connections are reused\u003c\/li\u003e\n\u003cli\u003eSuits DD605, DS605 and DD60 DishDrawer models on file\u003c\/li\u003e\n\u003cli\u003eAlso listed for DD90SDFTM, DD90SDFTX and DD90STI\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003ePack size\u003c\/th\u003e\n\u003ctd\u003e2 actuators\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWiring\u003c\/th\u003e\n\u003ctd\u003eNot included\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eReplacing DishDrawer lid actuators\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall and turn off the water supply. Access to the actuators varies by model, so check the service information for your drawer before you start. Photograph the wiring and how each actuator mounts before removing it. Fit both new actuators, reconnect the original wiring and run a short cycle to check the lid lowers and the drawer stays dry.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDoes this kit include the wiring?\u003c\/h3\u003e\u003cp\u003eNo. The kit contains two lid actuators without wiring. Your existing wires connect to the new actuators, so check the old wiring and connectors are in good condition before fitting them.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547394797646,"sku":"522085","price":121.84,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/522085-genuine-fisher-and-paykel-dishdrawer-lid-actuator-kit-pack-of-2.jpg?v=1792025511"},{"product_id":"764570114-generic-dishwasher-lower-spray-arm","title":"764570114 Generic Lower Spray Arm suits Smeg Dishwashers DWA6214S DWA6314X2 DWA147X DWA314X DWAU315X1 DWAI6214X DWA6214W DWA157X DWA315X","description":"\u003cp\u003eThis generic lower spray arm is a compatible replacement for Smeg parts 764570114 and 764570188. It's an aftermarket arm rather than a Smeg branded one, made to suit Smeg dishwashers such as the DWA147X and DWA157X, the DWA314X and DWA315X, plus DWA6214S, DWA6314X2 and DWAU315X1. Fit it when the old arm is cracked, warped or no longer spinning freely.\u003c\/p\u003e\n\u003ch2\u003eSmeg dishwasher not cleaning the bottom rack\u003c\/h2\u003e\n\u003cp\u003eThe lower spray arm sits under the bottom basket and spins on jets of water forced out through its nozzles, blasting the dishes from below. When the arm cracks, water escapes through the split instead of the jets, so pressure drops and the arm may stop turning. Blocked nozzles, a broken hub or a bent arm that catches on the basket cause the same problem. The usual result is dirty plates and pots on the lower rack and gritty residue in corners, while the top basket still comes out clean. Spin the arm by hand and look for cracks along its length.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGeneric replacement for Smeg 764570114\u003c\/li\u003e\n\u003cli\u003eAlso replaces 764570188\u003c\/li\u003e\n\u003cli\u003eLower spray arm that sits under the bottom basket\u003c\/li\u003e\n\u003cli\u003eSuits Smeg DWA, DWAU and DWAI models on file\u003c\/li\u003e\n\u003cli\u003eCompatible aftermarket part, not made by Smeg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eChanging the lower spray arm\u003c\/h2\u003e\n\u003cp\u003eWith the dishwasher switched off at the wall, roll out the lower basket. Most lower arms lift straight off or release with a twist of the centre hub. Clear the hub seat and filter area of any debris before fitting the new arm, then press it on and spin it by hand to confirm it turns without catching on the basket or the filter.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs this the Smeg branded spray arm?\u003c\/h3\u003e\u003cp\u003eNo. It is a generic, compatible spray arm made to suit dishwashers that use Smeg arm 764570114 or 764570188. Check your dishwasher model against the models for this arm before ordering.\u003c\/p\u003e","brand":"Universal","offers":[{"title":"Default Title","offer_id":44547431104590,"sku":"764570114_G","price":72.6,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/764570114-generic-dishwasher-lower-spray-arm.jpg?v=1792025585"},{"product_id":"h0120400061fa-genuine-fisher-and-paykel-dishwasher-wash-pump-with-heater","title":"H0120400061FA Genuine Wash Pump with Heater for Fisher \u0026 Paykel Dishwashers DW60FC6X1 DW60FC6W1 DW60CKX1 DW60CKW1 DW60UC6X DW60UD6X1","description":"\u003cp\u003eH0120400061FA is the genuine Fisher \u0026amp; Paykel wash pump with an integrated heater, often called a heat pump, for a group of 60cm F\u0026amp;P dishwashers. The numbers H0120400061A, H0120400061B and H0120400061F are linked to it as well. Models on file include the DW60FC6X1 and DW60FC6W1, the DW60CKX1 and DW60CKW1, DW60U6I1, DW60UC6X and DW60UC6B, and DW60UD6X1 and DW60UD6B1.\u003c\/p\u003e\n\u003ch2\u003eFisher \u0026amp; Paykel dishwasher not heating or not washing\u003c\/h2\u003e\n\u003cp\u003eThis pump does two jobs. It drives water up through the spray arms under pressure, and the heater built into its housing warms that water as it circulates. That's why a failed heat pump can show up in two ways. If the motor side fails, the dishwasher fills and drains but you won't hear the wash running, and dishes stay dirty. If the heater side fails, the wash runs but the water stays cold, dishes come out greasy and the cycle may stall or show a heating fault. A leak from the pump body can be another sign.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part H0120400061FA\u003c\/li\u003e\n\u003cli\u003eWash pump with built-in heater\u003c\/li\u003e\n\u003cli\u003eLinked numbers H0120400061A, H0120400061B and H0120400061F\u003c\/li\u003e\n\u003cli\u003eListed for DW60FC, DW60CK, DW60UC, DW60UD and DW60UZ6B models on file\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting the heat pump\u003c\/h2\u003e\n\u003cp\u003eUnplug the dishwasher, turn off the tap and remove the kickboard. Soak up any water left in the sump. On many models the base is reached by sliding the machine out and laying it on its back on a blanket. Photograph the wiring and hoses before you disconnect them. Fit the new pump with fresh clamps if the old ones are tired, then run a short cycle and check for leaks.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eMy old pump says H0120400061A, is this the right one?\u003c\/h3\u003e\u003cp\u003eH0120400061A, H0120400061B and H0120400061F are all listed against this part, so H0120400061FA is the one to order for the models on this page. Confirm your dishwasher model on the label on the edge of the door first.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547434807374,"sku":"H0120400061FA","price":210.71,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120400061fa-genuine-fisher-and-paykel-dishwasher-wash-pump-with-heater.jpg?v=1792025781"},{"product_id":"4055710117-genuine-westinghouse-dishwasher-drain-hose-2m","title":"4055710117 Genuine Dishwasher Drain Hose 2m for Westinghouse Dishwashers WSF6606X WSF6606W WSF6606XA WSF6608X WSF6608W WSF67381S WSU67381S","description":"\u003cp\u003eA split or kinked outlet hose is a common cause of water under a dishwasher. Part 4055710117 is the genuine 2m (200cm) drain hose for a group of Westinghouse dishwashers, also listed as 42005936. It suits the WSF6606W and WSF6606X, the WSF6606XA, and the WSF6608W and WSF6608X, along with the WSF67251S, WSF67381S and WSU67381S.\u003c\/p\u003e\n\u003ch2\u003eDishwasher leaking or not draining? Check the drain hose\u003c\/h2\u003e\n\u003cp\u003eThe drain hose carries waste water from the dishwasher's pump to your sink waste or standpipe. It lives behind the machine and under the sink, where it can be kinked when the dishwasher is pushed back, squashed by stored items, or worn through where it rubs on the cabinet. Hoses also crack with age. A kinked or blocked hose leaves dirty water sitting in the bottom of the tub at the end of a cycle, while a split one leaks under the cabinet, often unnoticed until the floor or kickboard swells. Check the full length for damage and sludge.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Electrolux group part 4055710117\u003c\/li\u003e\n\u003cli\u003eAlternative number 42005936\u003c\/li\u003e\n\u003cli\u003e2m (200cm) drain hose\u003c\/li\u003e\n\u003cli\u003eListed for Westinghouse WSF6606 and WSF6608 models plus WSF67251S, WSF67381S and WSU67381S\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e2m (200cm)\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eReplacing the drain hose\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off at the wall and shut the water tap. Slide the machine out, put a towel and tray under the pump connection and disconnect the old hose at both ends. Fit the new hose to the pump with its clamp, route it without kinks and keep a high loop under the bench before connecting to the waste. Run a rinse and check both ends for drips.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eCan I extend the drain hose?\u003c\/h3\u003e\u003cp\u003eJoining extra hose on adds leak points and can make the pump work harder. This hose is 2m long, so measure the run from the dishwasher to your sink waste before ordering, and follow the installation guide for your model if you need more length.\u003c\/p\u003e","brand":"Electrolux","offers":[{"title":"Default Title","offer_id":44547436314702,"sku":"4055710117","price":66.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/4055710117-genuine-westinghouse-dishwasher-drain-hose-2m.jpg?v=1792025685"},{"product_id":"523727nap-genuine-fisher-and-paykel-dishdrawer-control-module-230v","title":"523727NAP Genuine DishDrawer Control Module for Fisher \u0026 Paykel Dishwashers DD60DCX7 DD60SCX7 DD60DCW7 DD60SDFTX7 DD60STI7 DD60DI7 DD60SCTX7","description":"\u003cp\u003eFisher \u0026amp; Paykel DD60 DishDrawer dishwashers with model numbers ending in 7 use genuine control module 523727NAP, a 230V board. Models on file include the DD60DCX7 and DD60DCW7, the DD60SCX7 and DD60SCW7, the DD60SCTX7, and integrated versions such as DD60DI7, DD60SI7 and DD60STI7. The DD60CCX7E and DD60DCW7E are on the list as well, so read the whole model number before ordering.\u003c\/p\u003e\n\u003ch2\u003eDishDrawer not starting or showing faults\u003c\/h2\u003e\n\u003cp\u003eThe control module is the brain of the DishDrawer. It reads the buttons and sensors, then runs the motor, water valve, heater and lid in the right order for each wash program. When it fails, the drawer may be completely dead, start and stop at random, ignore the buttons, or throw fault codes that come back after a reset. Water reaching the electronics, power surges and age are common causes. Fault codes can also point to a pump, valve or sensor problem, so rule those out before replacing the module.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 523727NAP\u003c\/li\u003e\n\u003cli\u003e230V control module\u003c\/li\u003e\n\u003cli\u003eSuits DD60 DishDrawer models ending in 7\u003c\/li\u003e\n\u003cli\u003eListed for DD60DCX7, DD60SCX7, DD60DI7 and DD60STI7, among others\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eVoltage\u003c\/th\u003e\n\u003ctd\u003e230V\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFitting the control module\u003c\/h2\u003e\n\u003cp\u003eIsolate the DishDrawer at the power point and close the water tap. Take photos of every connector before unplugging anything, and handle the new module by its edges. The way in differs between models, so check the service guide for your drawer first. With mains wiring involved, this is a job for a qualified appliance technician.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWill this module fit a DD60 model ending in 6?\u003c\/h3\u003e\u003cp\u003eIt is listed for DD60 models ending in 7, plus the DD60CCX7E and DD60DCW7E. Drawers from other series may use a different module, so check the full model number on your product label before ordering.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547437789262,"sku":"523727NAP","price":197.12,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/523727nap-genuine-fisher-and-paykel-dishdrawer-control-module-230v.jpg?v=1792025517"},{"product_id":"140000059034-genuine-electrolux-sump-to-water-softener-hose-370mm","title":"140000059034 Genuine Sump to Water Softener Hose 370mm for Electrolux Group Dishwashers","description":"\u003cp\u003eElectrolux part 140000059034 is a genuine 370mm dishwasher hose that runs between the sump and the water softener unit. It's a small internal hose, but a split or perished one can cause leaks under the machine or upset how the softener is supplied with water. As there's no confirmed model list on file, match 140000059034 against your dishwasher's parts list or the old hose before ordering.\u003c\/p\u003e\n\u003ch2\u003eDishwasher leaking from underneath? Check the softener hose\u003c\/h2\u003e\n\u003cp\u003eDishwashers with a built-in water softener pass water through a resin container that removes hardness minerals, which helps prevent white spots and scale. This hose links the softener to the sump at the base of the wash cabinet. With heat, detergent and age, rubber hoses harden, crack and loosen at their joints. A leak here often shows up as water in the base tray, a leak protection error, or a damp floor under the machine. White residue on dishes can also point to a softener problem.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Electrolux part number 140000059034\u003c\/li\u003e\n\u003cli\u003eJoins the sump to the water softener\u003c\/li\u003e\n\u003cli\u003e370mm long\u003c\/li\u003e\n\u003cli\u003eInternal dishwasher hose\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e370mm\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eReplacing an internal dishwasher hose\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off at the wall and close the tap before sliding it out. Soak up any water sitting in the base tray first. Note the hose route and clamp positions with a photo, as the hose must not kink or rub once the machine is back in place. Fit the new hose, secure the clamps, top up the softener salt if needed and run a short program to check for leaks.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWill 140000059034 suit my dishwasher?\u003c\/h3\u003e\u003cp\u003eIt suits Electrolux built dishwashers whose parts list shows this number. Compare the length and end shapes with your old hose, which should measure about 370mm, to be sure before you order.\u003c\/p\u003e","brand":"Electrolux","offers":[{"title":"Default Title","offer_id":44547439394894,"sku":"140000059034","price":11.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/140000059034-genuine-electrolux-sump-to-water-softener-hose-370mm.jpg?v=1792025688"},{"product_id":"524867-genuine-fisher-and-paykel-dishdrawer-crockery-insert-with-trapdoor-and-fold-down","title":"524867 Genuine DishDrawer Crockery Insert with Trapdoor, Clips and Fold-Down Racks for Fisher \u0026 Paykel Dishwashers DD60DCW6 DD60DCX6","description":"\u003cp\u003ePart 524867 is the genuine Fisher \u0026amp; Paykel crockery insert assembly for DishDrawer dishwashers. It's the comb section in the basket that keeps plates standing upright, and it arrives as a kit with the trapdoor, clips and fold-down racks. Listed fits include the DD60DCW6 and DD60DCX6. If your old basket carries the earlier numbers 522942 or 522944, the 524867 is the current replacement for them.\u003c\/p\u003e\n\u003ch2\u003eWhen the plate rack in your Fisher \u0026amp; Paykel DishDrawer breaks\u003c\/h2\u003e\n\u003cp\u003eInside the drawer, the crockery insert spaces plates and bowls apart so the spray can reach both faces of each item. Its racks fold flat when you need the room for saucepans or baking trays. All that folding takes a toll. Hinge points crack, clips work loose and individual tines snap off. Once that happens, plates slump against each other or topple over mid-cycle, and they come out with dried food still stuck on. A loose insert section can also shift around in the basket every time the drawer is opened.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part number 524867\u003c\/li\u003e\n\u003cli\u003eCrockery insert assembly with trapdoor\u003c\/li\u003e\n\u003cli\u003eSupplied with clips and fold-down racks\u003c\/li\u003e\n\u003cli\u003eReplaces earlier numbers 522942 and 522944\u003c\/li\u003e\n\u003cli\u003eListed for DishDrawer models DD60DCW6 and DD60DCX6\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting the new insert\u003c\/h2\u003e\n\u003cp\u003eOpen the drawer fully and lift out the basket so you can work on it at the bench. Take a photo of how the old insert sits and where each clip locates before you unclip anything. Fit the new insert one clip at a time and press each one until it seats firmly. Fold the racks up and down a few times to check they move freely, then load a couple of plates to confirm they stand straight.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDoes the 524867 come with new clips?\u003c\/h3\u003e\u003cp\u003eYes. It's supplied as an assembly that includes the trapdoor, the clips and the fold-down racks, so there's no need to salvage clips from the broken insert. Check the photo of your old setup to see where each one goes.\u003c\/p\u003e\n\u003ch3\u003eIs this the left or right side insert?\u003c\/h3\u003e\u003cp\u003eParts listings show 524867 as the right-hand insert set, with the left-hand set sold under its own number, 524868. Look at which side of your basket is damaged before you order, and order both if both are broken.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547444506702,"sku":"524867","price":51.81,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/524867-genuine-fisher-and-paykel-dishdrawer-crockery-insert-with-trapdoor-and-fold-down.jpg?v=1792025518"},{"product_id":"524185p-genuine-fisher-and-paykel-dishdrawer-motor-rotor-assembly-ph3","title":"524185P Genuine DishDrawer Motor Rotor Assembly PH3 for Fisher \u0026 Paykel Dishwashers DD603 DS603 DD601 DS601 DD603I DS603I DD602","description":"\u003cp\u003eFisher \u0026amp; Paykel part 524185P is the genuine PH3 motor rotor assembly for DishDrawer dishwashers, the no notch version of this rotor. It replaces the earlier numbers 525884P and 524307P. It's listed for the DD601, DD602 and DD603 double drawers and the DS601 and DS603 single drawers, including integrated versions such as the DD603I and DS603I.\u003c\/p\u003e\n\u003ch2\u003eDishDrawer not washing or making a grinding noise\u003c\/h2\u003e\n\u003cp\u003eThe DishDrawer wash motor is split in two. The stator stays under the tub, while the rotor sits down in the sump and spins the impeller that drives water up to the spray arm. Broken glass, bone or grit can chip the impeller or jam the rotor, and wear can leave it running out of true. Typical symptoms are a grinding or rattling noise, dishes coming out dirty, water left in the drawer, or a motor fault code. A rotor that wobbles or has damaged vanes needs replacing.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 524185P\u003c\/li\u003e\n\u003cli\u003ePH3 rotor, no notch version\u003c\/li\u003e\n\u003cli\u003eReplaces 525884P and 524307P\u003c\/li\u003e\n\u003cli\u003eRotor O-ring is a separate part, number 523049\u003c\/li\u003e\n\u003cli\u003eSuits DD601, DD602, DD603, DS601 and DS603 models\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eVersion\u003c\/th\u003e\n\u003ctd\u003ePH3, no notch\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFitting the rotor\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall. Take out the filter and the sump parts that sit above the rotor, then lift the old rotor out. Inspect the O-ring and replace it if it's flattened or cracked, since a tired O-ring can leak. Drop the new rotor in, refit the sump parts and filter, then run a rinse cycle and listen for smooth running.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDoes this rotor come with the O-ring?\u003c\/h3\u003e\u003cp\u003eThe O-ring that seals around the rotor is listed as its own part, 523049. If the old one is worn, flattened or nicked, order it at the same time so the new rotor seals properly.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547459645518,"sku":"524185P","price":121.84,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/524185p-genuine-fisher-and-paykel-dishdrawer-motor-rotor-assembly-ph3.jpg?v=1792025517"},{"product_id":"h0120200324-genuine-fisher-and-paykel-dishwasher-lower-basket-axle-stub","title":"H0120200324 Genuine Lower Basket Axle Stub for Fisher \u0026 Paykel, Haier Dishwashers DW60FC4X1 DW60FC6X1 DW60CHX1 HDW13V1S1 HDW15V2S2","description":"\u003cp\u003eIf a wheel keeps falling off the bottom basket, the little axle it spins on has probably snapped. H0120200324 is the genuine axle stub for the bottom basket in Fisher \u0026amp; Paykel and Haier dishwashers. It's listed for Fisher \u0026amp; Paykel DW60FC, DW60CH and DW60U models such as the DW60FC4X1 and DW60FC6X1, and for Haier HDW13 and HDW15 dishwashers including the HDW13V1S1 and HDW15V2S2.\u003c\/p\u003e\n\u003ch2\u003eDishwasher bottom basket wheel falling off\u003c\/h2\u003e\n\u003cp\u003eThe lower basket rides in and out on small wheels, and each wheel turns on a stub axle fixed to the basket frame. Over time the stub wears thin or snaps, especially when the basket is pulled out loaded with heavy pots and pans. The result is a wheel that drops off, a basket that tilts or drags, and a rack that scrapes the door or jumps off the tub rails. Replacing a broken stub costs far less than buying a whole new basket.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine part H0120200324\u003c\/li\u003e\n\u003cli\u003eAxle stub for a lower basket wheel\u003c\/li\u003e\n\u003cli\u003eSuits Fisher \u0026amp; Paykel DW60 series dishwashers\u003c\/li\u003e\n\u003cli\u003eAlso listed for Haier HDW13 and HDW15 dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting the axle stub\u003c\/h2\u003e\n\u003cp\u003eNo tools are usually needed. Pull the lower basket out of the dishwasher and turn it over on a towel. Remove any broken pieces of the old stub, fit the new one in the same spot and refit the wheel. Spin the wheel by hand to make sure it turns freely before sliding the basket back in.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWill this fit a Haier dishwasher?\u003c\/h3\u003e\u003cp\u003eYes, as long as your model is on the list. H0120200324 is on file for Haier HDW13 and HDW15 dishwashers as well as Fisher \u0026amp; Paykel DW60 models. Check the model label on the inner edge of the door before ordering.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547470688334,"sku":"H0120200324","price":9.98,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120200324-genuine-fisher-and-paykel-dishwasher-lower-basket-axle-stub.jpg?v=1792025780"},{"product_id":"668114-genuine-gaggenau-dishwasher-drain-hose","title":"668114 Genuine Dishwasher Drain Hose for Gaggenau Dishwashers DF260161 DF261161 DF240161 DF241161 DF260141 DF260761 DF241761, BSH 00668114","description":"\u003cp\u003ePart 668114 is a genuine BSH dishwasher drain hose, sold under the Bosch parts banner and also listed as 00668114. It carries the waste water from the drain pump out to your sink trap or standpipe. Parts listings tie it to Gaggenau dishwashers in the DF240, DF241, DF260 and DF261 series, including the DF260161 and DF261161. Check your model plate against the list before ordering.\u003c\/p\u003e\n\u003ch2\u003eDishwasher not draining or leaking under the sink\u003c\/h2\u003e\n\u003cp\u003eEvery pump out sends the dirty water through this hose. When it's kinked, split or partly blocked, you'll notice water left sitting in the bottom of the tub after a cycle, a slow or laboured pump out, or a puddle on the floor near the sink. Food scraps and grease build up inside the hose over the years, and a hose that has been squashed behind the cabinet can crack along a fold. If you can hear the pump running but the water isn't leaving, the drain hose is one of the first things to inspect.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine BSH part number 668114\u003c\/li\u003e\n\u003cli\u003eAlso listed as 00668114\u003c\/li\u003e\n\u003cli\u003eDrain hose from the dishwasher pump to the household drain\u003c\/li\u003e\n\u003cli\u003eListed for Gaggenau DF240, DF241, DF260 and DF261 series dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eReplacing the drain hose\u003c\/h2\u003e\n\u003cp\u003eTurn the dishwasher off at the wall and shut off the water tap. Keep a towel and a shallow tray handy, because the old hose will still hold some water. You'll usually need to slide the machine out of its cavity to reach the pump connection. Route the new hose without kinks, secure it to the sink trap or standpipe with a suitable clamp, then run a rinse cycle and check both ends for drips.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs 668114 the same part as 00668114?\u003c\/h3\u003e\u003cp\u003eYes. BSH part numbers are often written with two leading zeros, so 668114 and 00668114 are the same drain hose. Whichever version appears on your old hose or in your manual points to this part.\u003c\/p\u003e","brand":"Bosch","offers":[{"title":"Default Title","offer_id":44547489824846,"sku":"668114","price":20.89,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/668114-genuine-gaggenau-dishwasher-drain-hose.jpg?v=1792025518"},{"product_id":"11033896-genuine-bosch-dishwasher-heat-exchanger-outlet-valve","title":"11033896 Genuine Heat Exchanger Outlet Valve for Bosch Dishwashers SMS63L08AU SMS63M28AU SMS46GI02A SMS46KI01A SMU66MS02A SMS66JI01A","description":"\u003cp\u003eBosch part 11033896 is the genuine outlet valve for the heat exchanger in a number of Bosch dishwashers, and it replaces the earlier 00631199. It's listed for SMS63L08AU and SMS63M28AU models, the SMS46GI, SMS46GW and SMS46KI ranges, the SMS66JI01A and the SMU66MS02A. Check the full E-Nr on your rating label, as each model comes in several production versions.\u003c\/p\u003e\n\u003ch2\u003eWhat the heat exchanger outlet valve does\u003c\/h2\u003e\n\u003cp\u003eMany Bosch dishwashers have a heat exchanger, a water tank built into the side wall that holds cold water to help with drying and pre-warming. This solenoid valve opens to empty that tank into the sump at set points in the program. When it fails, the machine's water levels get out of step, which can show up as error codes, poor drying, water left in the tub or odd filling behaviour. A leaking valve can also let water into the base and trip the anti-flood protection.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Bosch part 11033896\u003c\/li\u003e\n\u003cli\u003eReplaces 00631199\u003c\/li\u003e\n\u003cli\u003eSolenoid outlet valve for the heat exchanger tank\u003c\/li\u003e\n\u003cli\u003eSuits SMS63, SMS46, SMS66 and SMU66 series dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eReplacing the outlet valve\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall and turn off the water tap. Pull the machine out from the cabinet and lay towels down, as the heat exchanger and hoses may still hold water. Take photos of the hose and wiring connections before removing the old valve. Fit the new one, check every clamp, then run a short program and watch for leaks.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eHow do I find my Bosch model number?\u003c\/h3\u003e\u003cp\u003eOpen the door and look along its top or side edge for the rating label. Note the full E-Nr, such as SMS63L08AU\/28, and the FD number. The E-Nr is the one to compare with the models listed for 11033896.\u003c\/p\u003e","brand":"Bosch","offers":[{"title":"Default Title","offer_id":44547508535374,"sku":"11033896","price":45.57,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/11033896-genuine-bosch-dishwasher-heat-exchanger-outlet-valve.jpg?v=1792025589"},{"product_id":"522843nap-genuine-fisher-and-paykel-dishdrawer-control-module-230v","title":"522843NAP Genuine DishDrawer Control Module for Fisher \u0026 Paykel Dishwashers DD60DCX6 DD60DCW6 DD60SCX6 DD60SCW6 DD60DI6 DD605","description":"\u003cp\u003eThis is the genuine Fisher \u0026amp; Paykel control module for 60cm DishDrawer dishwashers, part number 522843NAP, rated 230V. You may also see it listed as 527715NAP. Fits on file include the DD60DCX6, DD60DCW6, DD60SCX6, DD60SCW6, DD60DI6 and the DD605 range. Tall drawer models are excluded, so double check your model number before ordering this board.\u003c\/p\u003e\n\u003ch2\u003eFisher \u0026amp; Paykel DishDrawer control board faults\u003c\/h2\u003e\n\u003cp\u003eThe control module is the brain of the drawer. It reads the touch buttons, opens the water valve, runs the wash motor and heating, and monitors the sensors through every stage of the cycle. When it fails, the drawer can be completely dead, show fault codes, beep or flash without starting, stop partway through, or refuse to fill, heat or drain even though those parts test fine on their own. Rule out wiring, plugs and the simpler parts first, because a control board is an expensive part to swap on a hunch.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part number 522843NAP\u003c\/li\u003e\n\u003cli\u003eAlso listed as 527715NAP\u003c\/li\u003e\n\u003cli\u003e230V control module for DD60 DishDrawer dishwashers\u003c\/li\u003e\n\u003cli\u003eListed for DD60DC, DD60SC, DD60DD, DD60SD and DD605 models\u003c\/li\u003e\n\u003cli\u003eNot for tall drawer models\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eVoltage\u003c\/th\u003e\n\u003ctd\u003e230V\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eChanging the control module\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall before removing the drawer front or any covers. If it's hard-wired, have a licensed electrician do the work. Photograph every plug and connector before you unplug the old module, and handle the new board by its edges to avoid static damage. Once it's in, run a full cycle and confirm the drawer fills, washes, heats and drains properly.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWill this module fit a tall DishDrawer?\u003c\/h3\u003e\u003cp\u003eNo. 522843NAP is listed for the standard height DD60 models shown on this page, and tall drawer models are excluded. Check the rating label, visible when the drawer is pulled out, for your exact model number before ordering.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547510829134,"sku":"522843NAP","price":215.94,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/522843nap-genuine-fisher-and-paykel-dishdrawer-control-module-230v.jpg?v=1792025517"},{"product_id":"h0120202828b-genuine-fisher-and-paykel-lower-basket-fold-down-clip-left-hand","title":"H0120202828B Genuine Lower Basket Fold Down Clip Left Hand for Fisher \u0026 Paykel, Haier Dishwashers DW60FC4X1 DW60FC6X1 DW60CHX1 DW60UC6X HDW15V2S2","description":"\u003cp\u003ePart H0120202828B is the genuine left hand fold down clip for the lower basket in Fisher \u0026amp; Paykel and Haier dishwashers. It suits a big group of models, including the Fisher \u0026amp; Paykel DW60FC4X1, DW60FC6X1, DW60CHX1 and DW60UC6X, and Haier machines such as the HDW14G2X, HDW15G3X and HDW15V2S2. Check which side the broken clip came from, as this listing is the left hand version only.\u003c\/p\u003e\n\u003ch2\u003eDishwasher tines falling down? Replace the basket clip\u003c\/h2\u003e\n\u003cp\u003eIn the lower basket, rows of fold down tines let you switch between standing plates upright and clearing a flat space for pots and pans. This clip holds the folding section in position. When it snaps or wears, the tines flop over during loading or collapse onto the dishes as the basket slides in and out, and plates no longer stand up properly to be washed. Clips also crack from being forced or from years of hot washes. Swapping the clip gets the basket working again and avoids replacing the whole basket.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel and Haier part H0120202828B\u003c\/li\u003e\n\u003cli\u003eLeft hand fold down clip for the lower basket\u003c\/li\u003e\n\u003cli\u003eSuits Fisher \u0026amp; Paykel DW60CC, DW60CE, DW60CH, DW60CK, DW60FC and DW60U models\u003c\/li\u003e\n\u003cli\u003eAlso listed for Haier HDW10F1S1, HDW14G2, HDW15G3, HDW15V2 and HDW15V3 dishwashers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eSide\u003c\/th\u003e\n\u003ctd\u003eLeft hand\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eClipping on the replacement\u003c\/h2\u003e\n\u003cp\u003eSlide the lower basket out to get good access. Note how the old clip sits on the basket wire and which way it faces, then remove any broken pieces. Line the new left hand clip up in the same spot and press it on until it snaps into place. Fold the tines up and down a few times to check they hold in both positions.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDo I need both left and right clips?\u003c\/h3\u003e\u003cp\u003eThis listing is the left hand clip only. If the clips on both sides of the basket are broken, you will also need the matching right hand clip, which is sold separately.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547582525518,"sku":"H0120202828B","price":12.08,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120202828b-genuine-fisher-and-paykel-lower-basket-fold-down-clip-left-hand.jpg?v=1792025779"},{"product_id":"h0120807893-genuine-haier-dishwasher-filter-assembly","title":"H0120807893 Genuine Dishwasher Filter Assembly, Filter Basket for Haier Dishwashers HDW15F1B1 HDW15F2B1 HDW15F3B1 HDW15F3S1","description":"\u003cp\u003eHaier's genuine filter assembly, part H0120807893, sits in the base of the tub and catches food scraps before the wash water is pumped back through the spray arms. It is listed for four Haier models, the HDW15F1B1, HDW15F2B1, HDW15F3B1 and HDW15F3S1. Replace it if yours is cracked, the mesh is torn or a piece has gone missing.\u003c\/p\u003e\n\u003ch2\u003eGritty dishes or a smelly Haier dishwasher\u003c\/h2\u003e\n\u003cp\u003eEvery wash, the water drains down through this filter, which holds back food, seeds, broken glass and other debris. Clean water carries on to the wash pump while the scraps stay behind. Once the filter cracks or the mesh tears, grit gets back onto the dishes and can reach the pump and the spray arm holes, causing blockages, noisy running and poor results. A dirty or damaged filter is also a common reason for bad smells and water left sitting in the bottom of the tub.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Haier part H0120807893\u003c\/li\u003e\n\u003cli\u003eFilter assembly that sits in the base of the dishwasher tub\u003c\/li\u003e\n\u003cli\u003eSuits Haier HDW15F1B1, HDW15F2B1, HDW15F3B1 and HDW15F3S1\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting and caring for the filter\u003c\/h2\u003e\n\u003cp\u003ePull out the lower basket and lift or twist the old filter out of the sump, following any arrows marked on it. Wipe out debris left in the sump before fitting the new filter, and make sure it locks fully in place, as a loose filter lets grit through. Rinse the filter under the tap every week or two to keep the dishwasher draining and cleaning well.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDoes this filter fit other Haier dishwashers?\u003c\/h3\u003e\u003cp\u003eH0120807893 is listed for the HDW15F1B1, HDW15F2B1, HDW15F3B1 and HDW15F3S1. Other Haier dishwashers can use a different filter, so check the model number on the label along the edge of the door before ordering.\u003c\/p\u003e","brand":"Haier","offers":[{"title":"Default Title","offer_id":44547584491598,"sku":"H0120807893","price":27.76,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120807893-genuine-haier-dishwasher-filter-assembly.jpg?v=1792025782"},{"product_id":"522090-genuine-fisher-and-paykel-dishdrawer-heater-plate-kit-230v","title":"522090 Genuine DishDrawer Heater Plate Kit 230V for Fisher \u0026 Paykel Dishwashers DD60DCX7 DD60SCX7 DD605 DS605 DD60DI7 DD60DCW7 DD60SCTX7 DD60DCX6","description":"\u003cp\u003eFor Fisher \u0026amp; Paykel DishDrawer dishwashers in the 605 family, part 522090 is the genuine 230V heater plate kit. It is listed for 47 models, from the DD605 and DS605 to the DD60DC, DD60SC, DD60SCT and DD60DDF series, including the DD60DCX7, DD60SCX7 and DD60DI7. Fit it when the drawer no longer heats the water or keeps tripping the power.\u003c\/p\u003e\n\u003ch2\u003eDishDrawer not heating water or tripping power\u003c\/h2\u003e\n\u003cp\u003eThe heater plate warms the water in the drawer during the wash so detergent can break down grease and food. When it fails, cycles may run cold, take much longer than usual, or stop with an error, and dishes come out greasy, cloudy or wet. A heater that has broken down internally can also leak current to earth and trip the safety switch as soon as heating starts. Hard water scale and food residue around the plate shorten its life, so keep the filter clean and use rinse aid.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 522090\u003c\/li\u003e\n\u003cli\u003eHeater plate kit, 230V\u003c\/li\u003e\n\u003cli\u003eSuits DD605, DS605, DD60DCX7, DD60SCX7 and DD60DI7\u003c\/li\u003e\n\u003cli\u003eListed for 47 DishDrawer models across the DD60DC, DD60SC, DD60SCT and DD60DDF ranges\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eVoltage\u003c\/th\u003e\n\u003ctd\u003e230V\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eReplacing the DishDrawer heater plate\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall and turn off the water before you begin. Expect to remove and partly strip down the drawer to reach the heater plate, so allow time and take photos as you go. Clean away scale and residue from the area around the plate, then reassemble and run a hot program to check it heats and doesn't leak. If you are unsure, have a qualified technician fit it.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWill this suit my DD60 DishDrawer?\u003c\/h3\u003e\u003cp\u003eIt is listed for 47 DishDrawer models in the 605 family, including the DD605, DS605, DD60DCX7, DD60SCX7 and DD60DI7. Find your model number on the drawer's serial label and match it to the list before ordering.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547633872974,"sku":"522090","price":80.03,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/522090-genuine-fisher-and-paykel-dishdrawer-heater-plate-kit-230v.jpg?v=1792025517"},{"product_id":"523049-generic-dishdrawer-rotor-o-ring-238-silicone","title":"523049 Replacement Silicone Rotor O Ring 238 suits Fisher \u0026 Paykel DishDrawer Dishwashers DD60DCX7 DD60SCX7 DD60DI7 DD60STI7 DD90STI2 DD60DCW7","description":"\u003cp\u003ePart 523049 is a silicone o ring, size 238, used around the motor rotor in Fisher \u0026amp; Paykel DishDrawer dishwashers. This is a replacement seal made to suit the Fisher \u0026amp; Paykel number rather than a Fisher \u0026amp; Paykel branded part. It is listed for the DD60DCX6, DD60DCX7, DD60DCW7, DD60SCX7, DD60DI7, DD60STI7 and DD90STI2. Many repairers fit a new one whenever the rotor is removed for service.\u003c\/p\u003e\n\u003ch2\u003eDishDrawer leaking under the drawer? Check the rotor o ring\u003c\/h2\u003e\n\u003cp\u003eIn a DishDrawer, the wash motor's rotor sits in the floor of the tub, and an o ring seals around it so water stays in the drawer instead of escaping underneath. Silicone stays flexible through hot washes, but over time the ring can flatten, harden, split or get nicked when the rotor is lifted out. A worn ring often shows up as water under the drawer, a leak error, or a drawer that won't run its cycle. Fitting a new o ring each time the rotor comes out is good insurance against leaks.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eRotor o ring for part number 523049\u003c\/li\u003e\n\u003cli\u003eSilicone, size 238\u003c\/li\u003e\n\u003cli\u003eReplacement seal made to suit Fisher \u0026amp; Paykel DishDrawers\u003c\/li\u003e\n\u003cli\u003eSuits the DD60DCX6 and DD60DCX7, the DD60SCX7 and DD60DI7, plus the DD60STI7 and DD90STI2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eSilicone\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSize\u003c\/th\u003e\n\u003ctd\u003e238\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFitting the rotor o ring\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall before working on it. Remove the filter and lift out the rotor following your model's service steps. Pick out the old o ring without scratching the groove, wipe the seat clean, and roll the new ring evenly into place without twisting it. Refit the rotor, then run a short program and check under the drawer for leaks.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs this a genuine Fisher \u0026amp; Paykel o ring?\u003c\/h3\u003e\u003cp\u003eNo. It is a silicone replacement made to suit Fisher \u0026amp; Paykel part number 523049, not a Fisher \u0026amp; Paykel branded seal. It is listed for the DishDrawer models shown above.\u003c\/p\u003e","brand":"Universal","offers":[{"title":"Default Title","offer_id":44547635413070,"sku":"523049_G","price":19.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/523049-generic-dishdrawer-rotor-o-ring-238-silicone.jpg?v=1792025515"},{"product_id":"524837-genuine-fisher-and-paykel-dishdrawer-rinse-aid-dispenser-cap-mid-grey","title":"524837 Genuine Rinse Aid Dispenser Cap Bung, Mid Grey for Fisher \u0026 Paykel DishDrawer Dishwashers DD60DCX9 DD60SCX9 DD60DAX9 DD60DCX7 DD90STI2","description":"\u003cp\u003eLost or cracked the rinse aid cap on your DishDrawer? Part 524837 is the genuine Fisher \u0026amp; Paykel rinse aid dispenser bung in mid grey, also listed as 527694. It suits DD60DAX9, DD60DCX9, DD60SCX9, DD60DDFX9 and DD60DDFB9 models, plus the DD60DCW7, DD60DCX7 and DD90STI2. A cap that seals properly keeps rinse aid where it belongs, so the reservoir lasts as long as it should.\u003c\/p\u003e\n\u003ch2\u003eRinse aid running out fast or leaking from the drawer\u003c\/h2\u003e\n\u003cp\u003eRinse aid sits in a small reservoir in the drawer and is dosed into the final rinse to help water sheet off the dishes so they dry without spots. This bung closes the filling point and keeps the rinse aid sealed in during the wash. When the cap cracks, loses its seal or goes missing, rinse aid washes out too quickly, the reservoir empties far sooner than it should, and you may see excess foam or streaks. A loose cap can also let wash water into the reservoir and dilute the rinse aid.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 524837\u003c\/li\u003e\n\u003cli\u003eAlso listed as 527694\u003c\/li\u003e\n\u003cli\u003eRinse aid dispenser cap bung in mid grey\u003c\/li\u003e\n\u003cli\u003eSuits DD60DCX9 and DD60SCX9 DishDrawers, plus the DD60DAX9 and DD60DDFX9\u003c\/li\u003e\n\u003cli\u003eAlso listed for the DD60DCW7, DD60DCX7 and DD90STI2\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eColour\u003c\/th\u003e\n\u003ctd\u003eMid grey\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFitting the rinse aid cap\u003c\/h2\u003e\n\u003cp\u003eOpen the drawer and wipe away any spilled rinse aid around the filling point, as even a few drops can cause heavy foaming on the next wash. Check the opening for cracks or old residue, then fit the new cap and turn or press it until it locks firmly. Top up the rinse aid first if the level is low.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs 527694 the same cap as 524837?\u003c\/h3\u003e\u003cp\u003eBoth numbers are listed for this mid grey rinse aid cap. If your manual or old part shows either one, this cap suits the DishDrawer models shown. Check your model number against the list to be sure.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547636985934,"sku":"524837","price":24.62,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/524837-genuine-fisher-and-paykel-dishdrawer-rinse-aid-dispenser-cap-mid-grey.jpg?v=1792025515"},{"product_id":"h0120801601-genuine-fisher-and-paykel-dishwasher-door-lock-hook-assembly","title":"H0120801601 Genuine Door Lock Hook Assembly for Fisher \u0026 Paykel, Haier Dishwashers DW60FC4X1 DW60FC6X1 DW60CHX1 DW60UC6X DW60UZ6B HDW15G3X HDW13G1X","description":"\u003cp\u003eWhen a dishwasher door won't stay shut, or the machine won't start because it thinks the door is open, the latch is the first thing to check. H0120801601 is the genuine door lock hook assembly used in both Fisher \u0026amp; Paykel and Haier dishwashers, including the DW60FC2X1, DW60FC4X1 and DW60FC6X1, the DW60CHX1 and DW60CKX1, DW60U models, and Haier HDW13G1X, HDW14G2X and HDW15G3X machines.\u003c\/p\u003e\n\u003ch2\u003eFisher \u0026amp; Paykel dishwasher door not latching\u003c\/h2\u003e\n\u003cp\u003eThe door lock holds the door firmly closed against the tub seal and tells the control that the door is shut so a wash can start. A plastic hook on the door engages the latch, and with thousands of openings the hook can wear, crack or snap, and the switch that senses the door can fail. Typical signs are a door that springs open, has to be slammed to latch, or closes but the dishwasher won't start, or stops partway through a cycle. Water dripping from the top of the door can also point to a latch that isn't pulling the door in tight.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel and Haier part H0120801601\u003c\/li\u003e\n\u003cli\u003eDoor lock and hook assembly\u003c\/li\u003e\n\u003cli\u003eSuits Fisher \u0026amp; Paykel DW60FC, DW60CH, DW60CK and DW60U dishwashers\u003c\/li\u003e\n\u003cli\u003eAlso listed for Haier HDW13G1, HDW14G2 and HDW15G3 models\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eFitting the door lock\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall before you start. The lock is normally reached by removing the inner door panel or the top trim, depending on the model. Photograph the wiring on the old lock, transfer the connections to the new one, and make sure the hook lines up with the latch opening. Close the door gently a few times to check it catches cleanly before running a wash.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDoes H0120801601 fit Haier dishwashers?\u003c\/h3\u003e\u003cp\u003eYes. As well as the Fisher \u0026amp; Paykel DW60 range, it is listed for Haier HDW13G1, HDW14G2 and HDW15G3 models, in both the W and X versions. Match the model number printed on the door edge label to be sure.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547653107790,"sku":"H0120801601","price":115.58,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120801601-genuine-fisher-and-paykel-dishwasher-door-lock-hook-assembly.jpg?v=1792025779"},{"product_id":"4933dd3001b-genuine-lg-dishwasher-door-hinge-rope-connector","title":"4933DD3001B Genuine Door Hinge Rope Connector for LG Dishwashers LD-1420W2 LD-1419W2 LD-1415W1 LD-1482W4 LD1452WFEN2 LD-1484T4 LD-14AT2","description":"\u003cp\u003ePart 4933DD3001B is a genuine LG connector that fastens the hinge rope inside the door mechanism of an LG dishwasher. It's listed for dozens of LG models, including the LD-1420, LD-1419, LD-1415, LD-1482 and LD-1484 series, plus LD1452 and LD-4000 range machines such as the LD-4120M. This version of 4933DD3001B has no hook on the end, so compare it with the part you're taking out.\u003c\/p\u003e\n\u003ch2\u003eLG dishwasher door falling open or feeling heavy\u003c\/h2\u003e\n\u003cp\u003eOn each side of the tub, a spring and rope work with the hinge to take the weight of the door as it opens and closes. The connector is the small fitting that holds the rope in place within that set-up. If it cracks or pulls apart, the spring can no longer counter the door's weight. The door then drops open with a thud, feels much heavier on one side, or won't stay level when lowered. Leaving it unrepaired puts extra load on the hinge and on the other side, so it's worth fixing early.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine LG part 4933DD3001B\u003c\/li\u003e\n\u003cli\u003eThis version has no hook\u003c\/li\u003e\n\u003cli\u003eHolds the door rope within the hinge and spring assembly\u003c\/li\u003e\n\u003cli\u003eSuits LG dishwashers such as LD-1420W2, LD-1482W4, LD1452WFEN2 and LD-4120M\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eChecking and replacing the connector\u003c\/h2\u003e\n\u003cp\u003eSwitch the dishwasher off at the wall and turn off the water tap before you start. You'll usually need to slide the machine out of its cavity to reach the sides of the tub. Before removing anything, photograph how the rope, connector and spring are routed. Fit the new connector in the same position, then open and close the door several times to make sure it moves evenly on both sides.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDoes this connector have a hook?\u003c\/h3\u003e\u003cp\u003eNo. This version of 4933DD3001B comes without a hook. Some LG dishwashers use a different connector that does have one, so look closely at the old part before ordering. If yours differs, send your model number through our parts enquiry form and we'll check it.\u003c\/p\u003e","brand":"LG","offers":[{"title":"Default Title","offer_id":44547669917774,"sku":"4933DD3001B","price":10.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/4933dd3001b-genuine-lg-dishwasher-door-hinge-rope-connector.jpg?v=1792025514"},{"product_id":"510852-genuine-fisher-and-paykel-dishdrawer-drain-hose-kit-3-8m","title":"510852 Genuine DishDrawer Drain Hose Kit 3.8m for Fisher \u0026 Paykel Dishwashers DD60DCX7 DD60DCW7 DD60SCX9 DD60DAX9 DD90STI2 DD605 DD24","description":"\u003cp\u003eFisher \u0026amp; Paykel DishDrawers pump their waste water out through a long flexible hose, and 510852 is the genuine replacement kit for that hose. At 3.8m it has a generous reach to the sink trap or standpipe. The kit is listed for DD60, DD605, DD90 and DD24 DishDrawers, including the DD60DCX7, DD60DCW7, DD60SCX9, DD60DAX9 and DD90STI2.\u003c\/p\u003e\n\u003ch2\u003eDishDrawer leaking or not draining properly\u003c\/h2\u003e\n\u003cp\u003eAfter each wash the drain pump pushes dirty water through this hose and out to the household drain. Under the bench the hose can get squashed by stored items, rub against the cabinet or perish with age. A split hose shows up as water pooling in the cabinet or under the kitchen floor, often only noticed once the timber swells. A kink or crushed section can leave water sitting in the bottom of the drawer after the cycle ends, or trigger a drain fault. Fitting a fresh hose clears both problems.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 510852\u003c\/li\u003e\n\u003cli\u003eDrain hose length 3.8m\u003c\/li\u003e\n\u003cli\u003eSupplied as a spare hose kit\u003c\/li\u003e\n\u003cli\u003eListed for DD60, DD605, DD90 and DD24 DishDrawer models\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e3.8m\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eReplacing the DishDrawer drain hose\u003c\/h2\u003e\n\u003cp\u003eTurn the power off at the wall and close the water tap. The DishDrawer usually has to come out of its cavity to reach where the hose joins the machine. Keep the new hose free of kinks and sharp bends, follow the drain height shown in the Fisher \u0026amp; Paykel installation guide, and secure the outlet end firmly. Run a short program and check for drips before sliding it back.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eWhich DishDrawers does this hose kit suit?\u003c\/h3\u003e\u003cp\u003eIt's listed for DD60, DD605, DD90 and DD24 DishDrawers, including the DD60DCX7, DD60DCW7, DD60SCX9, DD60DAX9 and DD90STI2. Check the model number on your product label against the list. If you can't find a match, send it through our parts enquiry form.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547673423950,"sku":"510852","price":70.62,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/510852-genuine-fisher-and-paykel-dishdrawer-drain-hose-kit-3-8m.jpg?v=1792025513"},{"product_id":"529730-genuine-fisher-and-paykel-dishdrawer-double-water-inlet-valve","title":"529730 Genuine Double Inlet Valve for Fisher \u0026 Paykel DishDrawer Dishwashers DD605 DD603 DD60DCX9 DD60DCX7 DD60DCW7 DD60DDFX7 DD60DI7 DD605I","description":"\u003cp\u003ePart 529730 is a genuine Fisher \u0026amp; Paykel double inlet valve, the solenoid valve that lets tap water into the machine on DD605, DD603 and DD60D series DishDrawers. It's also listed under the older numbers 526850 and 522146. Models on file include the DD605I and DD605FD, the DD60DCX9, DD60DCX7 and DD60DCW7, and the DD60DDFX7 and DD60DI7.\u003c\/p\u003e\n\u003ch2\u003eDishDrawer not filling or overfilling\u003c\/h2\u003e\n\u003cp\u003eThe valve sits between the water supply hose and the dishwasher. When the controller calls for water, it energises a coil that pulls the valve open, and when the coil switches off a spring snaps it shut. With two coils in one body, a double valve can serve both drawers. A coil that burns out leaves a drawer that won't fill and shows a water fault. Debris on the inlet screen gives slow filling, while a valve that sticks open can let water keep trickling in and flood the drawer or the floor. A hairline crack in the body often shows as drips below the machine.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Fisher \u0026amp; Paykel part 529730\u003c\/li\u003e\n\u003cli\u003eAlso listed as 526850 and 522146\u003c\/li\u003e\n\u003cli\u003eDouble solenoid inlet valve\u003c\/li\u003e\n\u003cli\u003eSuits DD605, DD603 and DD60D series DishDrawers\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eReplacing the double valve\u003c\/h2\u003e\n\u003cp\u003eIsolate power at the wall and turn the water off at the tap before touching the machine. Disconnect the inlet hose and keep a container handy, as some water will run out. Label each wire or take a photo so every coil goes back on the right terminal. Fit the new valve, reconnect the hose with its sealing washer and turn the tap on slowly while you watch for leaks.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eIs 529730 the same as 526850?\u003c\/h3\u003e\u003cp\u003eYes. 526850 and 522146 are earlier Fisher \u0026amp; Paykel numbers for this double inlet valve, and 529730 is the number it's sold under now. If your machine or parts list shows either older number, this valve is the one to order.\u003c\/p\u003e","brand":"Fisher \u0026 Paykel","offers":[{"title":"Default Title","offer_id":44547688038478,"sku":"529730","price":67.48,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/529730-genuine-fisher-and-paykel-dishdrawer-double-water-inlet-valve.jpg?v=1792025517"},{"product_id":"h0120200964-genuine-haier-dishwasher-lower-basket-roller-no-axle","title":"H0120200964 Genuine Lower Basket Roller Wheel for Haier Dishwashers, Bottom Rack Wheel Only, No Axle","description":"\u003cp\u003eH0120200964 is a genuine Haier roller wheel for the lower basket of Haier dishwashers. It is supplied as the wheel only, without an axle. If the axle on your basket is also broken or missing, it is available separately as H0120200965, and a complete roller with axle is sold as H0120200346. When the axles on your basket are intact, the wheel alone is all you need.\u003c\/p\u003e\n\u003ch2\u003eDishwasher bottom basket not rolling properly\u003c\/h2\u003e\n\u003cp\u003eThe lower basket runs on a set of rollers that let it glide out over the open door and back into the tub. A broken, cracked or missing wheel makes the basket drag, tilt to one side or drop off its track, which can jam it against the door, scratch the tub and even stop the door closing properly. A lopsided basket also shifts the dishes, so the spray arm can catch on plates and wash results suffer. Swapping worn wheels is a quick, low cost repair that saves replacing the whole basket.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Haier part number H0120200964\u003c\/li\u003e\n\u003cli\u003eLower basket roller wheel\u003c\/li\u003e\n\u003cli\u003eSupplied without an axle\u003c\/li\u003e\n\u003cli\u003eAxle sold separately as H0120200965\u003c\/li\u003e\n\u003cli\u003eComplete roller and axle available as H0120200346\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003eSupplied as\u003c\/th\u003e\n\u003ctd\u003eWheel only, no axle\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFitting a lower basket roller\u003c\/h2\u003e\n\u003cp\u003eWith the dishwasher off and cool, pull the lower basket out and lift it free so you can work on a bench. Look closely at how the old wheel is retained on its axle, then ease it off, taking care not to snap the axle. Clip the new wheel on, spin it to check it turns freely and slide the basket back in to make sure it runs straight. Replace any other worn wheels at the same time.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eDo I need the axle as well?\u003c\/h3\u003e\u003cp\u003eOnly if the axle on your basket is broken or missing. H0120200964 is the wheel only. Order H0120200965 for the axle, or H0120200346 for a complete roller that includes both.\u003c\/p\u003e","brand":"Haier","offers":[{"title":"Default Title","offer_id":44547699867726,"sku":"H0120200964","price":9.98,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/h0120200964-genuine-haier-dishwasher-lower-basket-roller-no-axle.jpg?v=1792025782"},{"product_id":"902979927-genuine-electrolux-dishwasher-salt-1kg","title":"902979927 Genuine Electrolux Dishwasher Salt 1kg Pack for Dishwashers with a Built-In Water Softener","description":"\u003cp\u003eElectrolux dishwasher salt, part 902979927, comes in a 1kg pack for dishwashers fitted with a built-in water softener. The salt goes into a reservoir in the floor of the tub, usually under the lower basket, and the machine uses it to recharge its softening resin. It is made for the job, unlike table or cooking salt, which can contain additives that upset the softener.\u003c\/p\u003e\n\u003ch2\u003eWhy your dishwasher needs salt\u003c\/h2\u003e\n\u003cp\u003eHard water leaves calcium and magnesium deposits on glassware, the heating element and inside the pipes. Dishwashers with a water softener pass incoming water through a resin that captures those minerals, and salt is used to flush and recharge the resin. When the salt runs out the softener stops working, and you start to see white spots, a cloudy film on glasses, gritty residue on dishes and scale around the door and tub. Many machines show a salt warning light when the reservoir is low. How often you top up depends on your water hardness setting.\u003c\/p\u003e\n\u003ch2\u003ePart details\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eElectrolux part number 902979927\u003c\/li\u003e\n\u003cli\u003e1kg pack\u003c\/li\u003e\n\u003cli\u003eFor dishwashers with a built-in water softener\u003c\/li\u003e\n\u003cli\u003eRefills the salt reservoir that recharges the softener\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ctable class=\"part-specs\"\u003e\u003ctbody\u003e\u003ctr\u003e\n\u003cth\u003ePack size\u003c\/th\u003e\n\u003ctd\u003e1kg\u003c\/td\u003e\n\u003c\/tr\u003e\u003c\/tbody\u003e\u003c\/table\u003e\n\u003ch2\u003eFilling the salt reservoir\u003c\/h2\u003e\n\u003cp\u003eTake out the lower basket and unscrew the salt cap in the floor of the tub. On the very first fill, many manuals ask you to add water to the reservoir before the salt. Use a funnel to pour salt in until full, wipe any spilt salt off the thread and tub, and screw the cap on tightly. Run a rinse or normal cycle straight away so stray salt does not sit in the tub and cause corrosion.\u003c\/p\u003e\n\u003ch2\u003eQuestions about this part\u003c\/h2\u003e\n\u003ch3\u003eCan I use table salt instead?\u003c\/h3\u003e\u003cp\u003eNo. Table and cooking salt can contain anti-caking agents and iodine that may damage or clog the softener. Use salt made for dishwashers, like this Electrolux 1kg pack.\u003c\/p\u003e\n\u003ch3\u003eDoes my dishwasher need salt?\u003c\/h3\u003e\u003cp\u003eOnly if it has a built-in water softener. Look for a screw cap in the floor of the tub under the lower basket, or a salt setting in the manual. Machines without a softener do not need it.\u003c\/p\u003e","brand":"Electrolux","offers":[{"title":"Default Title","offer_id":44547708518478,"sku":"902979927","price":4.99,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0768\/3489\/7998\/files\/902979927-genuine-electrolux-dishwasher-salt-1kg.jpg?v=1792025594"}],"url":"https:\/\/partsshop.com.au\/collections\/dishwasher-parts.oembed","provider":"My Store","version":"1.0","type":"link"}